Publicidad
Idiomas disponibles
Idiomas disponibles
• In case of tools adapted for fastening of grinding wheels with
a threaded opening, make sure the grinding wheel thread
length is suitable for the spindle thread length.
• Always secure the workpiece. It is always preferable to secure
the workpiece in a vice or other fastening tool than holding
it in your hand.
• If own weight of the workpiece does not guarantee a stable
position, it should be fastened.
• Do not touch cut-off and grinding wheels, before they cool
down.
• Do not exert lateral pressure on the grinding or cut-off wheel.
• Do not cut a workpiece of a thickness larger than the
maximum cutting depth of the cut-off wheel.
• When quick release flange is used, make sure that inner flange
seated on the spindle is equipped with rubber O-ring and this
ring is not damaged. Also surfaces of the outer flange and the
inner flange must be clean.
• Use quick release flange only with cutting and grinding discs.
Use only flanges that are free from defects, that operate
correctly.
• In case of temporary mains power failure or after
disconnecting plug from mains socket with the switch in ON
position, unlock the switch and set it to OFF position before
starting the tool again.
NOTE: The tools is intended for indoor works.
Despite using the construction, which is safe by design itself,
protection means and additional safety features, there is always
a residual risk of injuries during operation.
Descriptions of used pictograms.
1
2
6
7
1.
Warning, take special precautions.
2.
Read the instruction manual, observe warnings and safety
conditions included in it!
3.
Use personal protection equipment (safety goggles, ear
protectors).
4.
Use safety gloves.
5.
Disconnect the power cord, before maintenance or repair works
are begun.
6.
Keep out of reach of children.
7.
Protect against rain
8.
Protection class II
DESIGN AND APPLICATION
The angle grinder is a hand-held power tool with the II class isolation.
The power tool is driven with a single-phase, commutator motor,
whose rotational speed is reduced by means of an intersecting
axis gear. The power tool can used both for grinding and cutting.
This type of power tools is widely used for removal of burrs from
metal surfaces, weld surface processing, cutting light-wall tubes and
other small metal objects etc. They are used in engineering industry,
automotive and chemical industry. With the use of proper tools, the
angle grinder can be used not only for cutting or grinding, but also
for rust and paint coats removal.
The areas of its application include repair and construction works,
not only related to metals. The angle grinder can also be used for
cutting and grinding of construction materials, such as brick, paving
stones, ceramic tiles, etc.
The power tool is designed for dry operation only and it must
not be used for polishing. The power tool should be used
according to its purpose.
3
4
5
8
Use inconsistent with its purpose
Do not work materials that contain asbestos. Asbestos is
carcinogenic.
Do not work materials, whose dust is inflammable or
explosive. During operation, the power tool produces sparks, which
may ignite emitted vapours.
Do not use cut-off wheels for grinding. The cut-off wheels are
used to cut with its face, while grinding with lateral surface of such
a cut-off wheel threatens with its damages and puts the operate
in danger of injuries.
DESCRIPTION OF GRAPHIC PAGES
The below list refers to device components shown in the graphic
pages of this instruction manual.
1.
Spindle lock button
2.
Switch
3.
Additional handle
4.
Grinding wheel cover
5.
External flange
6.
Internal flange
* There can be differences between the drawing and actual product.
DESCRIPTION OF USED GRAPHIC SIGNS
NOTE
WARNING
FITTING/SETTING
INFORMATION
EQUIPMENT AND ACCESSORIES
1.
Grinding wheel guard
2.
Socket spanner
3.
Additional handle
PREPARATION FOR WORK
ATTACHING THE ADDITIONAL HANDLE
The additional handle (3) is installed in one of the holes in the
grinder head. It is recommended to use the grinder with the
additional handle. When holding the grinder with both hands (also
using the additional handle), there is less risk of touching the grinder
wheel or brush with your hand, as well as of injuries during recoil.
ADJUSTABLE MAIN HANDLE
The wheel guard protects the operator against flying broken
pieces and accidental contact with a working tool or sparks. The
guard should always be fitted. Special attention should be paid
so that its covering part faces the operator.
Install the grinding wheel guard (4) so the protrusion on its clip
matches the notch on the grinder gear casing.
The wheel guard can be set in any position.
Secure the mounting bolt.
The removal and adjustment of the wheel guard are performed in a
reverse order to its installation.
REPLACEMENT OF WORKING TOOLS
When working tools are replaced, wear working gloves at all
times.
The spindle lock button (1) is only designed to lock the grinder
spindle, when a working tool is installed or removed. Do not use
it as a braking button, when the wheel rotates. Otherwise, the
grinder may become damaged or the user may be injured.
INSTALLING THE WHEELS
When grinding or cut-off wheels with the thickness below 3 mm
are installed, the outer flange nut (5) should be tightened with
the flat surface from the wheel side (fig. B).
Press the spindle lock button (1).
13
- 1 pce
- 1 pce
- 1 pce
Publicidad
