Publicidad
Idiomas disponibles
Idiomas disponibles
How to operate the freewheel mode
• The front wheel has two modes of
operation:
– Unlocked mode: When
the pedals are turning
independently from the front
wheel (freewheel).
– Locked mode: When the
pedals and the front wheel are
connected together and move
as one.
• To put the front wheel in unlocked
mode (freewheel), locate the side of the front wheel with the
large red button marked with the unlock icon. Turn the front
wheel until one of the arrows around the front wheel hub is
aligned with the dot on the button, and then push the button
until you hear a click.
• To put the front wheel in locked mode, locate the side of the
front wheel with the large red button marked with the lock
icon. Turn the front wheel until one of the arrows around the
front wheel hub is aligned with the dot on the button, and
then push the button until you hear a click.
WARNING! Freewheel function is to be used only with the parent
handle (push bar).
WARNING! Check that the push bar (parent handle) is locked in
position before use.
WARNING! Automatic freewheeling ensures the tricycle can be
pushed safely while the child's feet rest on the pedals without
the pedals turning.
How to operate the parking devices
Use the parking devices to lock the rear wheels and keep the
trike stationary when required.
• To lock the parking devices, stop
the trike and push down the red
parking device on the left wheel
with your foot. Once you hear a
click, the parking devices will be
locked and the trike will remain
stationary.
• To unlock the parking devices,
push down the red parking device
on the right wheel with your foot.
Once you hear a click, the parking
devices will be unlocked and the
trike will be mobile.
WARNING! The parking devices located on the rear wheels
are NOT TO BE USED TO SLOW DOWN the trike. The left parking
device is designed to put the trike into a stationary mode after
stopping the trike. The parking devices are not designed for
other purposes. Using the parking devices to slow down the trike
will cause irreparable damage to the rear wheels' mechanism
and must be avoided at all times.
How to operate the handlebar lock mechanism
To operate the handlebar lock mechanism, observe the
recommended settings below.
• For infant trike: While facing the front of
the trike, push the handlebar lock on the
handlebar column to your right to enable
front wheel steering only on the parent
handle (push bar).
• For guided trike, training trike and
balance bike: While facing the front of
the trike, push the handlebar lock on
the handlebar column to your left to
enable front wheel steering on both the
handlebars and the parent handle (push
bar).
B. Transforming INFANT TRIKE to GUIDED TRIKE (18-36 months)
In guided trike mode, your child will start to use the pedals.
Ensure that his/her feet are resting correctly and flat on the
pedals.
– Remove the parent handle (push bar) from the trike by
pressing the red release button on the bottom rear of the trike
frame and sliding the bar out.
– Remove the left and right safety bars from the handlebars by
sliding the release buttons under the handlebars.
– Under the saddle, turn the knob 90 degrees to unlock and
remove the harnessed seat.
– Reattach the parent handle (push bar) to the trike by sliding
the security ring up the bar, and inserting the bar through the
holes located on the back of the saddle and trike frame. Push
the parent handle down until the steering shaft at the end of
the bar clicks into the trike frame.
– Press the red buttons at the base of the handlebars to rotate
the handlebars toward the front.
CAUTION! To avoid scratches or injury, slide the security ring
down the parent handle (push bar) until the ring sits on the
saddle.
– While facing the front of the trike, push the handlebar lock
on the handlebar column to your left to enable front wheel
steering on both the handlebars and the parent handle (push
bar).
– Store the harnessed seat for the next child:
a. Simultaneously press the large red buttons located on
both sides of the seat to fold the backrest.
b. Remove the left and right safety bars from the seat by
pressing the 2 red release buttons on the lower back of
the backrest.
c. Attach the safety bars to the 2 loops on the back of the
backrest.
d. Pinch the 2 red tabs together on the back of the headrest
to fold it backward.
e. Fold the canopy toward the back.
a
b
c
1
2
1
2
1
1
2
d
e
ENGLISH
15
Publicidad
