Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
-
Never immerse the appliance in water or other liquid.
-
Do not use abrasive cleaners or scouring pads to clean the product.
-
Use a damp sponge to clean the product surface. You can use a non-abrasive liquid
detergent or a mild spray solution to prevent stains from building up. Apply the cleaning
product to the sponge and not to the device surface directly.
-
To clean the glass door, use a glass cleaner or mild detergent and a damp sponge or soft
plastic scouring pad. Do not use abrasive products or metallic scouring pads, as they may
scratch the surface of the device.
-
Clean the control panel with a soft and damp cloth. Apply the cleaning product to the cloth,
do not apply it directly to the control panel. Cleaning the control panel with a scouring pad
or abrasive products may scratch it.
Interior cleaning
To clean any splashes that may occur during cooking processes, use a soft, damp sponge to
wipe the walls. You can use a non-abrasive liquid detergent or a mild spray solution to prevent
stains from building up. Apply the cleaning product to the sponge and not the inside directly.
Warning
Extreme caution when cleaning the heating element to avoid damaging it. Allow the device to
cool down completely and then carefully rub a soft, damp sponge or cloth along the resistors.
Do not use any type of cleaning product or detergent. Dry all the surfaces and allow them
to dry completely before connecting the power cord to the power outlet and turning on the
device.
Fat-drip tray cleaning
-
After every use, remove the fat-drip tray and wash it. Use a damp sponge to clean the tray.
You can use a non-abrasive liquid detergent or a mild spray solution to prevent stains
from building up. Apply the cleaning product to the sponge and not to the tray directly. Dry
it properly.
-
To get rid of fat, soak the tray in soapy water and wash it with a sponge or soft plastic
scouring pad. Rinse and dry well.
-
Always make sure to insert the fat-drip tray back into the device after cleaning and before
connecting the power cord to the mains socket or switching on the device.
-
The fat-drip tray is not dishwasher-safe.
Accessories cleaning
-
Wash all accessories in warm soapy water and use a sponge or a soft plastic scouring pad.
Rinse and dry thoroughly.
-
Do not use abrasive cleaners, scouring pads or metal utensils to clean any of the
accessories, as this may damage the surface.
-
Accessories are not dishwasher safe.
48
BAKE&FRY 2500 TOUCH STEEL
Storage
-
Make sure all its parts are clean and dry when you store it.
-
Make sure the door is closed.
-
Store the device cool, on a horizontal surface and on the support feet. Do not store it while
it is hot or wet.
-
Do not store it in hot and humid environments.
5. TROUBLESHOOTING
Error code
Problem
E1
Temperature sensor. Open
circuit.
E2
Temperature sensor.
Overheating or short circuit.
6. TECHNICAL SPECIFICATIONS
Ref. 02264
Model: Bake&Fry 2500 Touch Steel
Power: 1600 W
Voltage and frequency: 220-240 V~, 50/60 Hz
Volume: 26L
Manufactured in China | Designed in Spain
ENGLISH
Solution
In the last 2 minutes after the
cooking process starts, the
device will beep 10 times.
Turn off the device and turn it
on again.
If the problem persists,
contact the official Technical
Support Service of Cecotec to
repair it.
5 seconds after starting the
cooking process, the device
will beep 10 times. Turn off
the device and turn it on
again.
If the problem persists,
contact the official Technical
Support Service of Cecotec to
repair it.
BAKE&FRY 2500 TOUCH STEEL
49
Publicidad
