Publicidad
Idiomas disponibles
Idiomas disponibles
Instruction manual
dust is present, your risk from these exposures varies, depending
on how often you do this type of work. To reduce your exposure
to these chemicals, any time you do pulverulent operations,
work in a well ventilated area and work with approved safety
EN
equipment, such as dust masks that are specially designed to
filter out microscopic particles.
•
If the appliance strikes a foreign body, examine the device
for signs of damage and carry out any necessary repairs before
restarting and continuing to work.
•
If the appliance starts to vibrate abnormally, turn it off
and check for the cause immediately. Vibration is generally a
warning of trouble.
•
Always switch off the appliance and wait until the device
completely stops whenever you leave the machine, before
carrying out maintenance, before checking, cleaning or working
on the appliance.
•
It is forbidden to move or modify any of the internal parts
of the device.
Specific safety rules
•
Always turn on the tool before setting it against the piece
you are working on.
•
Large variations in temperature can lead to condensation
on live part. Before use: Give the machine time to adjust to the
temperature of the work area.
•
Do not use machines. tools and recommended accessories
for works other than those for which they are designed!
•
Secure the workpiece. Use clamping devices or a vise to
hold the workpieces securely.
•
When not in use, during breaks, when doing adjustment
works, changing accessories or during repair, always unplug the
cable.
•
When working: Do not allow the motor to stall under load.
•
Whenever possible, use a vacuum extractor for dust
collection. Remove dust and other waste matter in an
environmentally safe way.
•
Remove any adjusting key or wrench before turning the
power tool on. A wrench or a key left attached to a rotating part
of the power tool may result in personal injury.
•
Take special care when sanding lead based paint: All persons
entering the work area, must wear a mask specially designed for
protection against lead paint dust and fumes.
•
Never use
workpieces.
•
Do not sand materials containing asbestos!
•
Fit only accessories with reattachable contact fastener
coatings to sanding plate.
•
Dust extractor holes on sanding paper and sanding plate
must correspond.
•
When sanding, avoid applying excessive pressure to sander
as otherwise it may be forced to a stop.
•
Never carry a plugged-in sander with your finger on the
switch.
All manuals and user guides at all-guides.com
the
machine for sanding
Unpacking
When unpacking, check to make sure that all components are
included. Refer to the drawings on this manual. If any parts are
missing or broken, please call IVT assistance center.
Fitting sanding sheets
•
Switch off tool and pull out mains plug.
•
The sanding plate is provided with a velcro-type fasten for
sanding sheets. This enables fast attachment of new sanding
sheets without the use of a clamping fixture.
Before attaching new sanding sheet beat any dust etc. out of
contact fastener on sanding plate.
•
Lay new sanding paper tightly over sanding plate, ensuring
that holes in sanding plate and paper correspond.
•
Coarse sand paper (grain 50) removes in general the bigger
part of the material and fine sand paper (grain 120) is used for
the finishing.
Replacing the sanding plate (4)
The plate (4) has to be replaced when the velcro has been worn
out.
Before replacing the plate disconnect the device from the
mains plug.
•
Remove the sanding paper of the sole.
•
Remove the screws which the plate is fixed to the sander.
•
Remove the plate (4).
•
Install the new plate (4) on the sander.
•
Tighten the screws.
Dust extraction
magnesium
Dust extraction prevents large accumulations of
dust, high concentrations of dust in the ambient
air, and facilitates disposal.
[F1]
It is necessary to use the dust bag (6) to gather the dust.
It is necessary to empty the dust bag in time.
14
ATTENTION
ATTENTION
ATTENTION
Publicidad
