Elite Si6130XP Manual De Usuario página 28

• Electrically isolate the work area so that people are protected. Do not remove the case of the machine or manipulate it
internally when it is connected to the power supply.
• Only connect the machine to a 110V (SI6130XP) o 220V (SI7160XP – SI7175XP – SI7200XP) 50/60Hz power source.
• Make sure the power board has the 60 Amp thermomagnetic switch and the ground connection properly connected.
• Make sure the power cord is properly connected to the electrical outlet. If you do install a plug, be sure to respect the
cable color codes. This should not be modified in any way, use plugs in accordance with the standard to reduce the risk of
electric shock.
• Turn off the equipment when you finish your work and disconnect it from the electrical outlet.
• Do not leave the equipment connected to the electrical outlet or with the switch in the ON position without attention.
• Only place the electrode holder clamp or torch on an insulated surface regardless of whether the electrode connected or
not. Avoid shorting with the work clamp (ground).
Remove the electrode from the electrode holder if the welding process is interrupted or has ended.
• Place the machine switch in the OFF position at the rear of the equipment and disconnect the power cord from the electrical
outlet each time changes are made in the work area, when removing the electrode holder, torch, or clamp. work (ground)
and when transporting or cleaning equipment.
• Pay special attention to the condition of the power cable, if the cable is damaged, repair it with a qualified electrician,
PREFERENTLY take it to an Authorized Service Center by UJUETA MÉXCIO, S.A. DE C.V.
• Avoid tensioning the cables, do not move the machine by dragging it from the cables, if you need to move it, disconnect
it from the outlet. Do not use the power cord to suspend the machine, move it, or pull it to disconnect it from the electrical
outlet. Keep the power cord away from heat, oils, pointed surfaces, or moving parts. A cable in poor condition increases the
risk of electric shock.
• Pay attention to the condition of the electrode holder, torch and work clamp (ground) cables, especially if they malfunction
during the welding application or when the application result is not adequate. Check the whole set: connectors, electrode
holder, torch, work clamp, repair or replace them with a qualified electrician, PREFERENTLY take it to an Authorized Service
Center by UJUETA MÉXICO, S.A. DE C.V.
• Avoid contact with the electrical circuit, it can have negative consequences for the operator's health.
• The low DC voltage of the machine output makes it suitable for use in confined or humid spaces. However, excessive
moisture or sweating on clothing should be avoided. Make sure there is an insulated surface where the machine can be
placed.
• Pay attention to grounding systems when welding on electrically operated equipment or systems. Improper connections to
your welding equipment can allow welding process current to flow through the grounding system. Always connect the work
clamp as close as possible to the welding area, avoid placing it in a random place.
• In the event of an accident, disconnect the machine from the electrical outlet immediately.
• Only allow qualified personnel to repair the machine with original spare parts, this guarantees that the machine remains in
optimal operating conditions.
• Keep the machine out of the reach of rain and do not use it in humid environments.
Risk generated by welding sparks
Sparks produced by the electric arc can cause fires or explosions if they come into contact with flammable or explosive
materials.
• Do not use the device in environments that present an explosion hazard or where there are flammable liquids, gases or
dust. The welders produce sparks and molten metal that can start a conflagration.
• Remove all flammable substances from the job site. Fire cannot be detected while using eye protection when welding.
• Do not carry out welding processes on containers, naval artifacts or pipes that have contained flammable liquids such as
gasoline, mineral oils or gas even if they were unoccupied a long time ago since a small quantity may represent an explosion
risk.
KEEP WORKiNG KEEP WORKiNG
Keep Working
S i S i 6 1 3 0 6 1 3 0
S i S i 7 1 7 5 7 1 7 5
02
X P S i X P S i 7 1 6 0 7 1 6 0 X P X P
X P S i X P S i 7 2 0 0 7 2 0 0 X P X P