Bostitch N58C-1-E Manual De Instrucciones página 9

ADJUSTING THE MAGAZINE
(All models EXCEPT N80CB-1ML-E, N8090CB-1ML-E)
1. The magazine contains an adjustable nail platform
on which the nail coil rests. The nail platform can
be adjusted up and down to specific nail settings.
2. To change settings, pull up on the post and twist
to the correct step. (Fig. 5)
TRIP OPERATION MODE
THESE TOOLS ARE FITTED WITH 2 DIFFFERENT
ACTUATION MODES DEPENDING ON THE MODEL.
m WARNING! Always disconnect air supply before
making adjustments as accidental actuation may
occur, possibly causing injury.
SEQUENTIAL ACTUATION MODE:
Models: N64084-2-E, N66C-2-E, N66FH-2-E, N75C-2-E,
N75CWW-2-M, N89C-2-E, N512C-2-E
CONTACT ACTUATION MODE:
Models: N58C-1-E, N64084-1-E, N64099-1-E,
N80CB-1ML-E, N8090CB-1ML-E, N89C-1P-E, N400C-1-E,
N401C-1-E
SEQUENTIAL ACTUATION
The sequential actuation requires the operator to
hold the tool against the work with the safety yoke
depressed before pulling the trigger. In order to drive
additional fasteners, the trigger must be released and
the tool lifted away from the work, before repeating the
above mentioned steps.
This makes accurate fastener placement easier,
for instance on framing, toe nailing and crating
applications. The sequential actuation allows exact
fastener location without the possibility of driving
a second fastener on recoil, as described under
Contact Trip (below). The sequential actuation tool
has a positive safety advantage because it will not
accidentally drive a fastener if the tool is contacted
against the work - or anything else - while the operator
is holding the trigger pulled.
CONTACT ACTUATION
THESE TOOLS ARE FITTED WITH CONTACT
ACTUATION.
m WARNING! Always disconnect air supply before
making adjustments as accidental actuation may
occur, possibly causing injury.
m WARNING! Tools marked with this
symbol have either contact actuation,
continuous contact actuation or selectable
actuation with contact actuation selected.
WHEN IN CONTACT ACTUATION MODE:
These tools are designed for use in
production applications such as pallets,
furniture, manufactured housing or
upholstery. DO NOT use for applications such as
closing boxes or crates and fitting transportation safety
systems on trailers and lorries. This tool shall only be
used in safe working places. Care must be taken to
prevent accidental actuation when changing from one
working position to another.
The common operating procedure on "Contact
actuation" tools is for the operator to actuate the
safety trip while keeping the trigger pulled, thus driving
a fastener each time the work is contacted. This will
allow rapid fastener placement on many jobs, such
as pallet assembly. All pneumatic tools are subject to
recoil when driving fasteners.
The tool may bounce, releasing the safety yoke and if
unintentionally allowed to re-contact the work surface
with the trigger still actuated (finger still holding the
trigger pulled) an unwanted second fastener will be
driven.
FASTENER DEPTH CONTROL ADJUSTMENT
N66C-2-E, N66FH-2-E, N75C-2-E, N75CWW-2-M ONLY
(Fig. 6)
The DIAL-A-DEPTH™ Fastener Control adjustment
feature provides close control of the fastener drive
depth; from flush with the work surface to shallow or
deep countersink.
First, set the air pressure for consistent drive in the
specific work, then use the DIAL-A-DEPTH™ Fastener
Control adjustment to give the desired depth of drive.
N58C-1-E, N64084-1-E, N64084-2-E, N64099-1-E,
N89C-1P-E, N89C-2-E, N400C-1-E, N401C-1-E,
N512C-2-E ONLY (Fig. 7)
The Fastener Depth Control Adjustment feature
provides control of the nail drive depth from flush with
or just above the work surface to shallow or deep
countersink.
GB
9