VERTO 52G576 Manual Original página 9

The electric mower is a device with class II insulation. It is driven by a single-
phase AC commutator motor. The mower is designed for mowing lawns in
the home garden. Only use accessories that are suitable for this device and
follow the instructions in the manual. The grass should be mowed in even
strips. The mower can be pushed or pulled. The mower is intended for
amateur use only.
It is not allowed to use the device inconsistently with its intended use.
DESCRIPTION OF THE GRAPHIC SIDES
The numbering below refers to the components of the device shown on
the graphic pages of this manual.
1. Switch lever
2. Safety button
3. Electric wire holder
4. Knob for fastening the guide
5. Grass outlet guard
6. Transport handle for the mower
7. Hubcap
8. Circle
9. Grass collector
10. Lower guide
11. Upper guide handle
12. Electric wire clips
13. Grass hopper full indicator
14. Cable and plug
* There may be differences between the drawing and the product.
DESCRIPTION OF THE GRAPHIC CHARACTERS USED
ATTENTION
WARNING
EQUIPMENT AND ACCESSORIES fig A
1. Body mower
2. Lower guide - right
3. Lower guide - left
4. Grass catcher, lower part
5. Grass catcher, upper part
6. Screws - 2 pcs.
7. Screws - 2 pcs.
8. Washers - 4 pcs.
9. Power cord clips - 2 pcs.
10. Clips for securing the wheels - 4 pcs.
11. Handle of the grass collector
12. Hubcaps of road wheels - 4 pcs.
13. Road wheels - 4 pcs.
14. Extension cord holder - 1 pc.
15. Knobs for mounting the lower and upper guide - 4 pcs.
PREPARATION TO WORK
Mounting the wheels
• Place the wheels on the axle fig. B1 and secure them with the clips
provided fig. B2.
• Put the wheel cover on and push it down until you hear a click, then the
wheel covers are installed fig B3
Installation of the lower guide
• Fit the screws (A) into the holes (B) in the housing fig C1
• Place the holder plate of the lower guide Fig. C2 on the installed screws,
and tighten it with the locking knob Fig. C2.
Note: The holes on the left and right holder plates are different, be
sure to install them correctly
Make sure that the mark (C) on the handle plate is aligned with one of the
three places (D) on the mower body Fig. C3
Note: The exact position of the marker depends on the height and
comfort of the user.
Mounting the upper guide
• Put the power cord holder on the upper guide as in fig. C4
• Assemble the upper guide to the lower guide with the locking knob,
washer fig. C5
Installation of the grass catcher
Insert the transport handle of the basket into the holes in the upper
•
part of the basket.
Then turn the cover over and secure the holder with the screws Fig.
•
D1
Fold the two parts of the grass collector, insert the tabs on the bottom
•
of the grass collector into the holes on the top and press them down
fig. D2
Installation of the basket in the mower
Raise the rear mower discharge cover deflector, place the grass
•
catcher under the steering wheel, then place the catcher on the pegs
(A) on the mower housing. fig D3
Lower the guard so that it rests on the grass catcher. figure D4
•
Mounting the power cord clip
• Install the clip to hold the power cord as shown in fig. E
OPERATION / SETTINGS
WARNING!
- Do not turn on the device until it is completely assembled. Before
switching on the appliance, always check the extension cord for signs of
damage, only use an undamaged extension cord.
Setting the cutting height
WARNING! Turn off the mower by releasing the switch lever and wait
for the motor and blade to stop before adjusting the cutting height, the
blades continue to rotate for a few seconds after the machine is turned off,
the rotating blade may cause injury.
For the first cut of the season, or after a long time from the last mowing,
select high cutting adjustment.
The cutting height can be selected from the following values: 20 mm, 35
mm, 50 mm
Setting the cutting height
Cutting height is adjusted by changing the height of the wheels
Turn the machine over, press the wheel axle with both hands towards
•
the center of the mower (blade)
Remove the axis from the cut and then move it to the required position
•
fig. F
Adjust the front and rear wheels in the same way so that the front and
•
rear wheels are in the same plane
All 4 wheels must be set to the same cutting height.
•
ATTENTION!
Place the axis in the upper position for the lowest cutting height.
•
Middle position for medium height and lowest position for highest cut.
Lowest cutting height is only suitable for short lawn trimming, high and
•
medium positions are recommended for normal use. Never use the
mower with the wheels in different positions.
For the first cut of the season, select high cut adjustment.
•
On tall grass, start mowing at the highest setting, then gradually lower
•
the cutting height.
Connecting the power
The mains voltage (230V) indicated on the rating plate must
•
correspond to the mains supply. The value of the current fuse should
be min. 10A
Insert the mower plug into the connection socket of the extension cord
•
Fig. G1
To prevent the extension cord from being disconnected during use, fit
•
the extension cord (cable end) through the loop and secure over the
hook before plugging in the plug Fig. G1
Switching the mower on and off
WARNING!
Do not turn on the device until it is completely assembled. Before switching
on the device, always check the connection for signs of damage, only an
undamaged connection can be used.
Note: A damaged extension cord can be very dangerous! It poses a
threat to the user's life and health!
If you try to start the mower in long grass, the engine may overheat and be
damaged
Turning on
• Press and hold the safety button (2) as shown in fig. G2. Pull the switch
lever (1) towards the steering wheel.
• The mower will start.
• Release the safety button.
Note: There is no need to press or hold the safety button after turning
on the device.
Turning off
To turn the mower off, release the switch lever (1). The mower will
•
then stop.
When and how to install and remove the grass collector
9