Stanley SCM701 Instrucciones Originales página 50

ENGLISH
they can easily shift slightly and very few rooms have exactly
square corners, all settings should be tested on scrap mould-
ing.
Alternative method for cutting crown moulding
Place the moulding at an angle between the fence (11) and
the saw table (36), with the top side of the moulding on the
table and the bottom side of the moulding on the fence as
shown in figure T1.
The advantage to cutting crown moulding using this method
is that no bevel cut is required. Minute changes in the mitre
angle can be made without affecting the bevel angle. This
way, when corners other than 90º are encountered, the saw
can be quickly and easily adjusted for them.
Instructions for cutting crown moulding angled
between the fence and base of the saw for all cuts
This saw can cut up to 9/16" (14 mm) x 3-5/8" (92 mm) crown
moulding nested.
Angle the moulding so the bottom of the moulding (part
u
which goes against the wall when installed) is against the
fence (11) and the top of the moulding is resting on the
saw table (36), as shown in figure T2.
The angled "flats" on the back of the moulding must rest
u
squarely on the fence and saw table (36).
Inside Corner
Mitre right at 45°
Left Side
Save right side of cut
Mitre left at 45°
Right Side
Save left side of cut
Special Cuts
Never make any cut unless the material is secured on the
table and against the fence.
Bowed material (fig. U1, U2)
When cutting bowed material always position it as shown in
figure U1 and never like that shown in figure U2. Positioning
the material incorrectly will cause it to pinch the blade near
the completion of the cut.
Cutting round material
Rounded material should be clamped or held firmly to the
fence to keep It from rolling. This is extremely important when
making angle cuts.
Cutting large material (fig. V)
Occasionally you will encounter a piece of wood a little too
large to fit beneath the lower guard. To clear the guard over
the wood, with the saw off and your right hand on the operat-
ing handle, place your right thumb outside of the upper portion
of the guard and roll the guard up just enough to clear the
wood, as shown in figure V. Release the guard prior to starting
50
(Original instructions)
Outside Corner
Mitre left at 45°
Save right side of cut
Mitre right at 45°
Save left side of cut
the motor. The guard mechanism will function properly during
the cut. Only do this when necessary.
NEVER TIE, TAPE, OR OTHERWISE HOLD THE GUARD
OPEN WHEN OPERATING THIS SAW.
Maintenance
Warning! To reduce the risk of serious personal injury, turn
tool off and remove the battery pack before transporting,
making any adjustments or removing/installing attachments or
accessories. An accidental start-up can cause injury.
Warning! To reduce the risk of serious personal injury, DO
NOT touch the sharp points on the blade with fingers or hands
while performing any maintenance. DO NOT use lubricants
or cleaners (particularly spray or aerosol) in the vicinity of the
plastic guard. The polycarbonate material used in the guard is
subject to attack by certain chemicals.
All bearings are sealed. They are lubricated for life and
u
need no further maintenance.
Periodically clean all dust and wood chips from around
u
AND UNDER the base and the rotary table. Even though
slots are provided to allow debris to pass through, some
dust will accumulate.
The brushes are designed to give you several years of
u
use. If they ever need replacement, return the tool to the
nearest service centre for repair.
Troubleshooting
Problem Possible Cause
Battery not installed.
Saw will not
Battery not charged.
start.
Brushes worn out
Dull blade.
Blade mounted
backwards.
Saw makes
unsatisfactory
cuts.
Gum or pitch on
blade.
Incorrect blade for
work being done.
Work light is
Battery not charged
flashing.
Saw not mounted
securely to stand or
work bench.
Machine
vibrates Stand or bench on
excessively. uneven floor.
Damaged saw
blade.
Solution
Install battery. Refer to Installing
and Removing Battery Pack.
Charge battery. Refer to Charging
Procedure.
Have brushes replaced by
authorised service centre.
Replace blade. Refer to Changing
or Installing a New Saw Blade.
Turn blade around. Refer to
Changing or Installing a New Saw
Blade.
Remove blade and clean with
coarse steel wool and turpentine or
household oven cleaner.
Change the blade type.
Charge battery. Refer to Charging
Procedure.
Tighten all mounting hardware.
Refer to Bench Mounting
Reposition on flat level surface.
Replace blade. Refer to Changing
or Installing a New Saw Blade.