Publicidad
Idiomas disponibles
Idiomas disponibles
• Installing the control box board
Use the 6-conductor cable to connect the box and the intercom panel, ensuring the colours match (fig.8) Insert
4 LR20 batteries into the electronic box to test the radio range. The antenna as far away as possible from all metal
surfaces, sources of interference and obstacles between the box and your home, (in particular, no leaves or
branches should touch it). For best results, it should also be placed high enough (approx. 1.6 m above ground level)
and be vertical.
N.B. :
If the transmission is of insufficient quality, use the 2 m cable supplied to find a better position for the
antenna.
Once the ideal location has been found, permanently mount the equipment:
Once you have found the ideal location :
1• Remove the cover from the box by unscrewing the 6 cross-head screws (H) (fig. 5).
Warning :
do not directly touch the electronic circuitry (see comment chapiter safety instruction : Important -
p3)
2• Fasten the box with two screws (J) at the top and bottom (fig. 6), The antenna is at the top right.
3• Remember to route the connecting cable for the roadside panel through the hole in the post first and 2 wires
(F) for the cabinet/electric strike link (it is thus necessary to bore the pillar or the wall consequently). The connection
(F) must to connect the other two wires to the lock or electric strike plate and on the connection «LOCK» of control
box.
N.B. :
Do not install an antenna other than the original one supplied
Warning :
Never insert the batteries before installation is completely finished.
• Installing the roadside panel
Tip :
we recommend running the cables (for the roadside panel and the electric strike plate) through a conduit to
protect them from impacts and the elements. To avoid oxidation and poor contacts, , do not trim the excess from
the 6-conductor cable. Instead, wind it around itself between the post and the electronic box.
1• Remove the cross-head screw (A)
2• Tip the roadside panel (B) toward the front and dislodge it from the bottom.
3• Using the 3 screws (K), mount the box (C) flush with the wall so that the slot (D) is facing the cable (E)
4• Fit a silicone* seal behind the Rain shield (C) to protect it from water running down the wall.
*
Do not use silicone-based acetic acid (vinegar smell)
5• Pass the connecting cable
6• Connect the 6 wires (E) to the back of the roadside panel
7• Check the orientation of the camera (G) (fig. 8).
VIDEO ( yellow ) GND ( black ) SPK (brown) MIC (white) KEY (green) VCC ( red )
8• Put the roadside panel back in place and fasten with the screw (A).
To complete installation of the roadside panel, open the battery compartment on the electronic box , box and
insert four 1.5 V alkaline LR20 batteries. , Be sure to follow the polarity markings. Close the battery compartment
and put the electronic box cover back in place with the 6 cross-head screws (H), Take care not to pinch or damage
the seal. You can use a low voltage supply power source, coming from a type WETR 14602 SER.R1 transformer or
from an automatic gate opener (12 ou 24 V / ). It should be connected on the terminals
tronic cabinet. In the case of direct voltage (V ) pay attention to the polarity +/-.
Warning :
If you do not use the batterie but by 12/24 V /
indicated Fig. 9
If you are using a 12/24 V /
Do not use rechargeable batteries.
(fig.5)
(fig.6 / 7 / 8)
power source, the batteries must be removed.
CFI EXTEL WEVA 2 - 01/2013
http://www.bakonline.net/
-
~
and
source (automatic opener) to connect as
+
~
of the elec-
GB4
Publicidad
