Kärcher SC 1 Premium Instrucciones De Operación página 9

Quick Reference
 Illustrations on Page 2
Illustration
 Remove the safety lock from the device.
 Fill the boiler with a maximum of 200 ml of fresh tap
water.
Illustration
 Screw in safety cap.
Illustration
 Insert the mains plug into a socket.
Indicator lamp glows green.
Illustration
 The steam cleaner is ready for use after approx. 3
minutes.
Illustration
 Connect the accessories to the steam nozzle or
steam gun.
Illustration
 Push the child lock at the top (steam button un-
locked).
 Push the steam button.
The steam cleaner is ready to use.
Operation
Attaching the Accessories
Illustration –
 If necessary, connect the required accessories
(see Chapter "Use of the accessories") with the
steam nozzle or steam gun.
 In order to do so, fit the open end of the accessory
to the steam nozzle or steam gun and push it on un-
til the unlocking button of the steam nozzle or
steam gun snaps in place.
Illustration
 Use the extension tubes if necessary. To do so,
connect one or both extension tubes to the steam
gun. Insert the required accessories on the free
end of the extension tube.
Removing the Accessories
 Push the child lock at the bottom (steam button
locked).
Illustration
 To detach the accessory parts, press the unlocking
button and pull the items apart.
Fill up with water
Notes
 In case of continuous use of commercially available
distilled water, no descaling of the boiler is neces-
sary.
 You can reduce the heating-up time by using warm
water.
 Remove the safety lock from the device.
 Fill the boiler with a maximum of 200 ml of fresh tap
water.
 Screw the safety cap back onto the device.
All manuals and user guides at all-guides.com
 Place the unit securely on a firm surface.
 Insert the mains plug into a socket.
Note
After approx. 3 minutes the steam cleaner is ready for
use.
 Push the child lock at the top.
 Actuate the steam lever to release steam.
Notes


Water needs to be filled into the boiler, if the steam vol-
ume decreases during work and no more steam is emit-
ted in the end.
Note
The safety lock cannot be opened as long as slight pres-
sure remains in the boiler.
 Push the steam button until no more steam is es-
 Push the child lock at the bottom.
 Disconnect the mains plug from the socket.
 Remove the safety lock from the device.
 Fill the boiler with a maximum of 200 ml of fresh tap
 Screw the safety cap back onto the device.
 Insert the mains plug into a socket.
 Push the child lock at the top.
Illustration
 Disconnect the mains plug from the socket.
 Push the steam button until no more steam is es-
 Push the child lock at the bottom.
Illustration
 Empty water out.
Illustration
 Coil the mains power cable around the water tank
 Allow the accessories to dry and then store them in
 Store the appliance at a dry and frost-proof loca-
– 9
EN
Turning on the Appliance
Indicator lamp must glow.
Upon initial start-up a small cloud of smoke may
exit the steam nozzle. The appliance requires a
short run-in time. At first, the escaping steam is ir-
regular and moist, some water drops may leak out.
The escaping amount of steam increases continu-
ously until the maximum amount is reached after
approx. one minute.
Do not tilt the appliance too much to the side during
cleaning work (max. angle 30°).
Otherwise the steam cleaner "spits" water.
Refilling Water
caping. Now, the boiler of the appliance is depres-
surized.
water.
The steam cleaner is ready to use.
Turning Off the Appliance
caping. Now, the boiler of the appliance is depres-
surized.
Storing the Appliance
and fasten with a cable clamp.
the accessories bag.
tion.
9