Publicidad
Remote control
■ Battery installation
1
Open the battery cover.
2
Insert the batteries according to the terminal indicated
in the battery compartment. When inserting or removing
the batteries, push it toward the (–) battery terminals.
3
Close the cover.
Caution:
● Replace all old batteries with new ones at the same
time.
● Do not mix old and new batteries.
● Remove the batteries if the unit will not be used for a
long period of time. This will prevent potential damage
due to battery leakage.
● Do not use rechargeable batteries (nickel-cadmium
battery, etc.).
● Installing the batteries incorrectly may cause the unit
to malfunction.
● Batteries (battery pack or batteries installed) shall not
be exposed to excessive heat such as sunshine, fire
or the like.
Notes concerning use:
● Replace the batteries if the operating distance is re-
duced or if the operation becomes erratic. Purchase 2
"AAA" size batteries (UM/SUM4, R3, HP-16 or similar).
● Periodically clean the transmitter on the remote control
and the sensor on the unit with a soft cloth.
● Exposing the sensor on the unit to strong light may in-
terfere with operation. Change the lighting or the direc-
tion of the unit.
● Keep the remote control away from moisture, heat,
shock, and vibrations.
■ Test of the remote control
The remote control can be used within the range shown below:
Remote sensor
0.2 m - 6 m
General control
■ To turn the power on
Press the ON/STANDBY button to turn the power on or off.
■ Display brightness control
Press the DIMMER button (remote control).
(Display is dim).
Dimmer 1
(Display gets dimmer).
Dimmer 2
(Display is bright).
Dimmer off
General control (continued)
■ Volume auto fade-in
If you turn off and on the main unit with the volume set to
27 or higher, the volume starts at 10 and fades in to the
last set level.
■ Volume control
Turn the volume knob toward VOLUME +/– (main unit) or
press VOL +/– (remote control) to increase or decrease
the volume.
■ Muting
To mute the volume, press the
Press again to restore the volume.
■ Direct key power on function
When you press any of the following buttons, the unit turns on.
CD / , USB / , BLUETOOTH / , AUDIO IN, TUNER,
●
OPEN/CLOSE (remote control): Selected function is
activated.
●
last function will start (CD, USB, BLUETOOTH, AUDIO
IN, TUNER)
■ Auto power off function
The main unit will enter the standby mode after approxi-
mately 15 minutes of inactivity during:
Audio In: No detection of input signal.
CD: In the stop mode or no disc.
USB: In the stop mode or no media.
Bluetooth: - No connection after approximately 15 minutes.
■ X-Bass control
When the power is first turned on, the unit is in the extra
bass mode. "X-BASS" indicator appears. To cancel this
mode, press the X-BASS button (remote control).
■ Bass or Treble control
1
2
MICRO COMPONENT SYSTEM XL-LS703B
Press SOUND (DEFAULT) button to return sound to
default settings. "SOUND DEFAULT" appears on the
display.
Sound default settings : Bass = 0, Treble = 0, X-Bass = off
■ Function
Press the FUNCTION button repeatedly to select desired
function.
Note:
The backup function will protect the memorised function
mode for a few hours should there be a power failure or
the AC power lead becomes disconnected.
E-5
/ (main unit): The unit turns on and playback of the
- In the pause or stop mode and no incoming signal
from device after approximately 15 minutes.
Press the BASS or TREBLE button to select "Bass" or "Tre-
ble" respectively.
Within 5 seconds, press the VOL (+ or –) button to adjust the
bass or treble.
- 5 ↔ - 4 ........ ↔ + 4 ↔ + 5
CD
FM STEREO
BLUETOOTH
button (remote control).
- 5 ↔ - 4 ........ ↔ + 4 ↔ + 5
FM MONO
AUDIO IN
USB
Publicidad
