Descargar Imprimir esta página

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Website: www.horizonglobal.com
Technical Assistance: 800-632-3290
TechnicalSupport@horizonglobal.com
To prevent SERIOUS INJURY, DEATH, or PROPERTY DAMAGE:
• ALWAYS read and follow all warnings and instructions included with
purchase before beginning installation. Keep for future reference.
• DO NOT exceed lower of towing manufacturing rating (including in your
vehicle owner's manual) or specific amperage ratings stated on product.
• ALWAYS read, understand and follow all warnings and instructions
printed on tow vehicle's battery.
• ALWAYS wear safety glasses and use all safety precautions during
installation
.
• Read and follow all warnings and cautions printed on the tow vehicle's
battery. All connections must be complete for T-One® Connector to
function properly. Test and verify installation with a test light or trailer
once installed. For initial test, reset vehicle electrical system by
temporarily removing the key from the ignition.
• DO NOT touch negative battery terminal to positive battery terminal.
Serious Injury and damage to Vehicle's electrical system can occur.
• If vehicle is equipped with the Start/Stop option, DO NOT connect the
module power wire to the support battery. Only connect module to the
main vehicle battery. Failure to connect to the vehicle main battery may
result in damage.
• Overloading circuits can cause fires.
• DO NOT exceed stated product ratings.
• Ensure all existing grounds connections are still attached. Torque Existing
ground screw to manufacture Torque Specifications.
©2023 Horizon Global™ Corp
Installation Instructions
PART NUMBER: 118882
1.
Limited Warranty. Horizon Global ("We" or "Us") warrants to the original consumer
purchaser only ("You") that the product will be free from material defects in both material
and workmanship for a specific period*, ordinary wear and tear excepted; provided that
installation and use of the product is in accordance with product instructions. THERE ARE
NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If the product does not
comply with this period specific limited warranty*, Your sole and exclusive remedy is that
We will replace the product without charge to You and within a reasonable time or, at our
option, refund the purchase price. This warranty is not transferable.
2.
Limitations on the Warranty. This limited warranty does not cover: (a) normal wear and
tear; (b) damage through abuse, neglect, misuse, or as a result of any accident or in any
other manner; (c) damage from misapplication, overloading, or improper installation,
including welds; (d) improper maintenance and repair; and (e) product alteration in any
manner by anyone other than Us, with the sole exception of alterations made pursuant to
product instructions and in a workmanlike manner.
3.
Obligations of Purchaser. To make a warranty claim, contact Us, at our principal address of
47912 Halyard Dr. Suite 100, Plymouth, MI 48170, 1-800-632-3290, identify the product by
model number, and follow the claim instructions that will be provided. Any returned
product that is replaced or refunded by Us becomes our property. You will be responsible
for return shipping costs. Please retain your purchase receipt to verify date of purchase and
that You are the original consumer purchaser. The product and the purchase receipt must
be provided to Us in order to process Your warranty claim.
4.
Remedy Limits. Repair or replacement is Your sole remedy under this limited warranty, or
any other warranty related to the product. We shall not be liable for service or labor
charges incurred in removing or replacing a product or any incidental or consequential
damages of any kind.
Assumption of Risk. You acknowledge and agree that any use of the product for any
5.
purpose other than the specified use(s) stated in the product instructions is at Your own
risk.
6. Governing Law. This limited warranty gives You specific legal rights, and You also may have
other rights which vary from state to state. This limited warranty is governed by the laws of
the State of Michigan, without regard to rules pertaining to conflicts of law. The state courts
located in Wayne County; Michigan shall have exclusive jurisdiction for any disputes
relating to this warranty.
LIMITED 1-YEAR WARRANTY
Sheet 1 of 24
118882-NP
Scan for safe towing
tip, or visit
http://qr.towingpro
ducts.net/qrproduct
s/qr-product
1/20/2023
Rev. A

Publicidad

loading

Resumen de contenidos para Horizon Global 118882

  • Página 1 TechnicalSupport@horizonglobal.com LIMITED 1-YEAR WARRANTY Limited Warranty. Horizon Global (“We” or “Us”) warrants to the original consumer To prevent SERIOUS INJURY, DEATH, or PROPERTY DAMAGE: purchaser only (“You”) that the product will be free from material defects in both material and workmanship for a specific period*, ordinary wear and tear excepted;...
  • Página 2 TechnicalSupport@horizonglobal.com qr-product Installation Difficulty: Application: Expert • Installation times are listed on Horizon Global websites or found in the downloadable Make Model application guides. Telluride • Installation difficulty levels are based on time and effort involved. They may vary depending on installer level of expertise and condition of the vehicle.
  • Página 3 Installation Instructions Always wear SAFETY GLASSES when installing wiring harness PART NUMBER: 118882 1. Open the rear hatch. Locate the plastic mount covers that 2. Using a Phillips Screwdriver or 10mm socket, remove the are covering the taillight mounting screws. Using a trim mounting screws on both driver’s side and passenger side...
  • Página 4 Using a trim panel tool, remove the 4 plastic clips, being carful to not damage them. Locate the 2 plastic retaining nuts. Using a 14mm socket remove the plastic nuts and set cover aside. ©2023 Horizon Global™ Corp Sheet 4 of 24 118882-NP 1/20/2023...
  • Página 5 Clean dirt and rustproofing from area. Verify what is behind any surface prior to drilling to avoid damage to the vehicle and/or personal injury. Do not drill into any exposed surfaces. ©2023 Horizon Global™ Corp Sheet 5 of 24 118882-NP 1/20/2023...
  • Página 6 Heat Shrinkable butt connector from the center out to the edges on each end until the tubing shrinks and sealant flows. Allow to cool before inspecting the splice. ©2023 Horizon Global™ Corp Sheet 6 of 24 118882-NP 1/20/2023...
  • Página 7 Heat Shrinkable butt connector from the center out to the edges on each end until the tubing shrinks and sealant flows. Allow to cool before inspecting the splice. ©2023 Horizon Global™ Corp Sheet 7 of 24 118882-NP 1/20/2023...
  • Página 8 Clean connection and add Dielectric grease (sold Separately) to the terminal Insure 4-Way Flat harness doesn’t Get pinched in Door latches, trailer pins. connection points or allow contact with road surface. Website: www.horizonglobal.com Technical Assistance: 800-632-3290 TechnicalSupport@horizonglobal.com ©2023 Horizon Global™ Corp Sheet 8 of 24 118882-NP 1/20/2023 Rev. A...
  • Página 9 GARANTIE LIMITÉE DE 1 AN Garantie limitée. Horizon Global (« Nous ») garantit uniquement à l’acheteur consommateur initial (« Vous ») que le produit sera exempt de défauts matériels et de Pour prévenir les BLESSURES GRAVES, LA MORT ou les DOMMAGES MATÉRIELS : fabrication pendant une période spécifique*, à...
  • Página 10 TechnicalSupport@horizonglobal.com Application: Difficulté d’installation: Experte Les temps d’installation sont répertoriés sur les sites Web d’Horizon Global ou dans les Faire Modèle guides d’application téléchargeables. Telluride • Les niveaux de difficulté d’installation sont basés sur le temps et les efforts impliqués. Ils peuvent varier en fonction du niveau d’expertise de l’installateur et de l’état du véhicule.
  • Página 11 Portez toujours des LUNETTES DE SÉCURITÉ lors de l’installation d’un faisceau de câblage NUMÉRO DE PIÈCE : 118882 2. À l’aide d’un tournevis cruciforme ou d’une douille de 10 mm, 1. Ouvrez le hayon arrière. Localisez les couvercles de support en retirez les vis de montage du côté...
  • Página 12 4 clips en plastique, en veillant à ne pas les endommager. Localisez les 2 écrous de rétention en plastique. À l’aide d’une douille de 14 mm, retirez les écrous en plastique et mettez le couvercle de côté. ©2023 Horizon Global™ Corp Feuille 12 de 24 118882-NP 1/20/2023 Rév.
  • Página 13 Vérifiez ce qui se trouve derrière toute surface avant le forage pour éviter d’endommager le véhicule et/ou de blesser. Ne percez pas dans les surfaces exposées. ©2023 Horizon Global™ Corp Feuille 13 de 24 118882-NP 1/20/2023 Rév. A...
  • Página 14 Connecteur bout à bout thermorétractable du centre vers les bords à chaque extrémité jusqu’à ce que le tube rétrécisse et que le mastic coule. Laisser refroidir avant d’inspecter l’épissure. ©2023 Horizon Global™ Corp Feuille 14 de 24 118882-NP 1/20/2023...
  • Página 15 Connecteur bout à bout thermorétractable du centre vers les bords à chaque extrémité jusqu’à ce que le tube rétrécisse et que le mastic coule. Laisser refroidir avant d’inspecter l’épissure. ©2023 Horizon Global™ Corp Feuille 15 de 24 118882-NP 1/20/2023...
  • Página 16 Site Web : www.horizonglobal.com Assistance technique : 800-632-3290 TechnicalSupport@horizonglobal.com ©Horizon Global™ Corp 2023 Feuille 16 de 24 118882-NP 1/20/2023 Rév. A...
  • Página 17 TechnicalSupport@horizonglobal.com GARANTÍA LIMITADA DE 1 AÑO Garantía limitada. Horizon Global ("Nosotros") garantiza únicamente al comprador consumidor original ("Usted") que el producto estará libre de defectos materiales tanto en materiales como en mano de obra durante un período específico*, exceptuando el desgaste Para prevenir LESIONES GRAVES, MUERTE o DAÑOS A LA PROPIEDAD:...
  • Página 18 Experto Hacer Modelo • Los tiempos de instalación se enumeran en los sitios web de Horizon Global o se Telluride encuentran en las guías de aplicaciones descargables. • Los niveles de dificultad de instalación se basan en el tiempo y el esfuerzo involucrados.
  • Página 19 Instrucciones de instalación Use siempre GAFAS DE SEGURIDAD al instalar el mazo de cables NÚMERO DE PIEZA: 118882 1. Abra la escotilla trasera. Localice las cubiertas de montaje de 2. Con un destornillador Phillips o un zócalo de 10 mm, retire plástico queestán cubriendo los tornillos de montaje de la luz...
  • Página 20 4 clips de plástico, teniendo cuidado de no dañarlos. Localice las 2 tuercas de retención de plástico. Con un zócalo de 14 mm, retire las tuercas de plástico y deje la cubierta a un lado. ©2023 Horizon Global™ Corp Hoja 20 de 24 118882-NP 1/20/2023 Rev.
  • Página 21 área. Verifique lo que hay detrás de cualquier superficie antes de perforar para evitar daños al vehículo y / o lesiones personales. No perfore ninguna superficie expuesta. ©2023 Horizon Global™ Corp Hoja 21 de 24 118882-NP 1/20/2023 Rev. A...
  • Página 22 Comenzando en el centro del conector de empalme. Conector a tope termorretráctil desde el centro hasta los bordes en cada extremo hasta que el tubo se encoge y el sellador fluye. Deje enfriar antes de inspeccionar el empalme. ©2023 Horizon Global™ Corp Hoja 22 de 24 118882-NP 1/20/2023...
  • Página 23 Comenzando en el centro del conector de empalme. Conector a tope termorretráctil desde el centro hasta los bordes en cada extremo hasta que el tubo se encoge y el sellador fluye. Deje enfriar antes de inspeccionar el empalme. ©2023 Horizon Global™ Corp Hoja 23 de 24 118882-NP 1/20/2023...
  • Página 24 Sitio web: www.horizonglobal.com Asistencia técnica: 800-632-3290 TechnicalSupport@horizonglobal.com ©2023 Horizon Global™ Corp Hoja 24 de 24 118882-NP 1/20/2023 Rev. A...