Publicidad
Idiomas disponibles
Idiomas disponibles
TRANSLATION OF
THE ORIGINAL INSTRUCTIONS
ELECTRIC MIXER
58G782
CAUTION: BEFORE USING THE POWER TOOL READ THIS MANUAL
CAREFULLY AND KEEP IT FOR FURTHER USE.
DETAILED SAFETY REGULATIONS
• Ensure the mains voltage matches the voltage on the tool label.
• Do not use the mixer in environments with potentially explosive
atmosphere. Do not mix solvents or substance containing
solvents with ignition temperature below 210°C.
• Do not wind the power cord around any part of the mixer body.
• Switch the mixer on and off only when the mixer paddle is
immersed in the tub.
• Ensure the tub for mixing is well fixed.
• Do not put your hands or any other objects into the tub when
mixing.
CAUTION! This device is designed to operate indoors.
The design is assumed to be safe, protection measures and
additional safety systems are used, nevertheless there is always a
small risk of operational injuries.
CONSTRUCTION AND USE
Electric mixer is a power tool designed for continuous use for
building industry and other fields. Possibility to use various mixing
tools appropriate for mixed substances allows for mixing of cement,
gypsum, stucco, paint, plaster, self levelling underlayment and other
chemicals. Depending on the composition being mixed and type of
the tool used, it is not recommended to mix more than 65 litres of
the product.
Use the power tool according to the manufacturer's instructions
only.
DESCRIPTION OF DRAWINGS PAGES
Below enumeration refers to the device elements depicted on the
drawing pages of this manual.
Mixer spindle
1.
Gear switch
2.
Switch
3.
Switch lock button
4.
Mixer shaft
5.
Mixing paddle
6.
Wheel for speed control
7.
* Differences may appear between the product and drawing
MEANING OF SYMBOLS
CAUTION
WARNING
ASSEMBLY/SETTINGS
INFORMATION
EQUIPMENT AND ACCESSORIES
Mixer shaft
- 1 pce
1.
Mixing paddle
- 1 pce
2.
Transport case
- 1 pce
3.
PREPARATION FOR OPERATION
Disconnect the power tool from power supply.
• Screw the shaft (5) into the mixer spindle (1) (fig. A).
• Screw the mixing paddle (6) to the shaft (5).
OPERATION / SETTINGS
SWITCHING ON / SWITCHING OFF
The mains voltage must match the voltage on the label of the
mixer.
The mixer is equipped with the switch, which protects against
accidental starting.
Switching on
• Press the switch lock button (4) located on the handle (fig. B).
• Press the switch button (3).
Switching off
• Release pressure on the switch button (3).
2 GEAR SELECTOR SWITCH
Rotational speed can be changed with the use of two-position gear
switch (2) (fig. C). Depending on the work being carried out, set the
gear switch to appropriate position.
• Position '1' is for lower speed and greater torque.
• After switching to the right, to position '2', the speed is greater
and the torque is lower.
• To restore lower speed set the switch back to the left position.
Never change the gear switch position under operation of the
mixer. It may damage the power tool. Turn the spindle slightly if
the switch position cannot be changed.
ROTATIONAL SPEED CONTROL
Wheel for rotational speed control (7) is located on the mixer handle
(fig. D). Control range is from 1 to 6, the speed can be changed
depending on the user's needs when working on either gear.
USE OF THE MIXER
• Ensure the power supply voltage is 230 V.
• Connect the power tool to the power supply network.
• During operation, always hold the mixer firmly (with both hands).
• Electronic controller allows for slow start of the mixing (no splash)
and slow stop.
• By turning the control wheel (7) you can increase or reduce
rotational speed of the spindle.
OPERATION AND MAINTENANCE
Unplug the power cord from the mains socket before
commencing any activities related to installation, adjustment,
repair or maintenance.
• Keep the mixer clean.
• When using the mixer always check that the ventilation holes are
not obstructed and no foreign body got between internal parts
of the power tool.
• Any maintenance or repairs should be carried out by an authorized
service workshop.
• During operation of the mixer, carbon brushes of the motor wear
out and they should be controlled and replaced regularly.
• Ball bearings of the mixer are greased for the whole time of mixer
operation.
REPLACEMENT OF CARBON BRUSHES
Replace immediately worn out (shorter than 5 mm), burnt or
cracked motor carbon brushes. Always replace both brushes at
a time.
Entrust replacement of carbon brushes only to a qualified person.
Only original parts should be used.
8
Publicidad
