Publicidad
Idiomas disponibles
Idiomas disponibles
POWERING & CONNECTING
Grounding the Switch
1. Remove the ground screw from the back of switch, and
connect one end of the ground cable to the wiring terminal
of switch.
2. Put the ground screw back into the screw hole, and tighten
it with a screwdriver.
3. Connect the other end of the ground cable to other device
that has been grounded or directly to the terminal of the
ground bar in the equipment room.
Powering on the Switch
Connect the power cable and the switch first, then
connect the power cable to the power supply system of
the equipment room.
Connecting Power Cord Anti-Trip
In order to protect the power supply from accidental
disconnection, it's recommended to use a power cord anti-trip
for installation.
1. Force the head of the fixing strap tightly into the hole next
to the power socket until it's buckled on the shell without
falling off.
2. After plugging the power cord into the power outlet, slide the
protector over the remaining strap until it slides over the end
of the power cord.
3. Wrap the strap of the protective cord around the power cord
and lock it tightly. Fasten the straps until the power cord is
securely fastened.
PORT CONNECTING
Connect to RJ45 Port
1. Connect one end of the network cable to the
switch, and the other end to the peer device.
2. After powered on, check the status of the
port indicator. If on, it means that the link is
connected normally; if off, it means the link is
disconnected, please check the cable and the
peer device whether is enabled.
Connect to SFP+ Port
The installation process of the fiber module is as follows:
1. Grasp the fiber module from the side and insert it smoothly along
the switch SFP+ port slot until the module is in close contact with
the switch.
2. When connecting, pay attention to confirm the Rx and Tx ports
of SFP+ fiber module. Insert one end of the fiber into the Rx and
Tx ports correspondingly, and connect the other end to another
device.
3. After powered on, check the status of the port indicator. If on,
it means that the link is connected normally; if off, it means the
link is disconnected, please check the cable and the peer device
whether is enabled.
Ground Terminal
Ground Cable
Ground Bar
Crystal head
Ethernet RJ45
RJ45
port
~ 3 ~
Notes:
• Please select the optical fiber cable according to the module type. The multi-mode module corresponds to the
multi-mode optical fiber, and the single-mode module corresponds to the single-mode optical fiber.
• Please select the same wavelength optical fiber cable for connection.
• Please select an appropriate optical module according to the actual networking situation to meet different
transmission distance requirements.
• The laser of the first-class laser products is harmful to eyes. Do not look directly at the optical fiber connector.
Connect to Console Port
1. Connect the console cable (prepared by yourself) to the DB9 male connector or USB port to the PC.
2. Connect the other end of the RJ45 end of the console cable to the console port of switch.
Connect to Console Port (DB9)
Notes:
• To connect, the steps order (1 -> 2) must be respected.
• To disconnect, the steps order is reversed (2 -> 1).
INSTALLATION
Install on the Desktop
1. Place the bottom of switch on a sufficiently
large and stable table.
2. Peel off the rubber protective paper of the
four footpads one by one, and stick them in
RJ45 port
the corresponding circular grooves at the
four corners of the bottom of the case.
3. Flip the switch over and place it smoothly
on the table.
Install on a 19" Standard Rack
1. Check the grounding and stability of the
rack.
2. Install the two L-shaped rack-mounting
in the accessories on both sides of
switch, and fix them with the screws
provided (KM 3*6).
SFP+
Port
3. Place the switch in a proper position in
Fiber
the rack and support it by the bracket.
module
4. Fix the L-shaped rack-mounting to the
guide grooves at both ends of the rack
with screws (prepared by yourself) to
ensure that the switch is stable and
horizontally installed on the rack.
Connect to Console Port (USB)
Rubber footpads
Circular groove
~ 4 ~
Publicidad
