Publicidad
Idiomas disponibles
Idiomas disponibles
Charging must be performed with the speci-
■
fied charger. If charging is performed with a
different charger, malfunctions can occur, or
the device might be damaged, explode or
generate heat.
Only charge the battery at the specified
■
voltage. Never use a charging voltage other
than the specified voltage. Failure to comply
could result in burns or heat formation.
Do not use any transformers such as boosters,
■
motor generators or DC sources to charge the
battery. Failure to comply will result in a fault
or deep discharging of the charger.
Do not charge the battery in the rain or in lo-
■
cations where it might be exposed to spray or
moisture. If the battery is charged while wet,
electric shocks or short-circuiting is possible,
which could result in burning and a fire.
Do not touch the mains plug with wet hands. If
■
you touch it with wet hands, you could receive
an electric shock.
Do not cover the charger with a cloth or sim-
■
ilar. Application of a cover can generate heat,
resulting in deep-discharging or a fire.
Do not place the charger close to a fire or
■
naked flame.
Do not charge the battery in the vicinity of
■
combustible substances.
Charge the battery in a well ventilated
■
location and protect it against direct sunlight.
Charging in direct sunlight may overheat
the charger, which could result in deep-dis-
charging or a fire.
Charge the battery in an ambient tempera-
■
ture range of 0°C to 40°C. If the ambient
temperature is below 0°C to 40°C, charging
may not be permissible because it could result
in a fire.
Do not allow any foreign bodies to get into
■
the ventilation openings or the battery contact
socket of the charger. Otherwise an electric
shock or other malfunctions could occur. Only
use the device in dust-free locations.
Handle the mains cable with care. If you
■
carry the mains adapter using the mains
cable or pull it out of the mains socket via the
mains cable, the cable could be damaged
or cracked, which in turn could lead to a
short-circuit. Ensure that it does not come into
contact with cutting blades, hot substances, oil
or grease. Replace a damaged mains cable
with a new cable.
140
Safety instructions
If the battery has been disconnected from
■
the tool housing, cover it with a sealing cap
until it is used again. To prevent short-circuits,
cover the terminal block (metal part) of the
unused battery with the cap provided with the
packaging.
Do not short-circuit the terminal block (metal
■
part) of the battery. If it is short-circuited, a
large current flows, overheating the battery,
which could result in burning or damage.
Do not throw the battery into the fire. Failure to
■
comply could result in an explosion.
When connecting the battery to the device,
■
observe the following to prevent malfunctions.
• Do not place your finger on the trigger.
• Do not press the contact arm against the
object.
• Keep your fingers or hand away from the
outlet opening. Note whether there is an op-
erating noise when you connect the battery.
— If you connect the battery and the contact
arm is pressed against the floor or similar,
the tool fan runs, this is, however, normal.
Be aware of changing noises or unusual
■
odours or noise. When the tool is activated
and then generates unusual odours or noise,
this is an indication of a fault. Use of the tool
in this condition can result in accidents. Con-
tact an authorised Würth dealer if anomalies
occur.
Disconnect the charger from the mains when it
■
is not being used.
Avoid direct sunlight. Do not leave the tool in a
■
vehicle or luggage compartment in which the
temperature could increase because otherwise
it might explode.
Keep the tool away from fires and naked
■
flames.
Ensure that you use the tool in a working
■
environment of -10°C to 40°C, because
otherwise the tool could ignite or explode. -10
°C or less: The tool body could be damaged.
40°C or greater: The fuel cell could be
damaged, which could result in ignition or
explosion.
Do not use the tool in the rain or in very damp
■
locations. Failure to comply could cause faults.
Be aware that the tool can become hot. If the
■
tool is used for a long time, the mouthpiece
and contact arm become hot. Take care to
avoid burns.
Publicidad
