Publicidad
Idiomas disponibles
Idiomas disponibles
English
mouth, eyes, or lay on the skin may promote absorption of
harmful chemicals. Direct particles away from face and body.
Use the appropriate dust extractor vacuum to remove
•
the vast majority of static and airborne dust. Failure
to remove static and airborne dust could contaminate the
working environment or pose an increased health risk to
the operator and those in close proximity.
DWST82800 Installation (Fig. A—D)
WARNING: Failure to comply with installation
may result in personal injury, product or
property damage.
Required Tools and Hardware
You will need to gather a few common tools and hardware.
Always consult your local building code for proper hardware.
•
Safety glasses
•
Pencil
•
Stud finder
•
Screwdriver
•
Drill
•
1/8" (3mm) drill bit
•
Level
•
#10 screws
3
‑
Use masonry screws for mounting to masonry block
or a concrete wall.
‑
Use the included #10 screws
wood studs.
CAUTION: Always use the correct screws for the
surface that D
WALT metal rail will be anchored in.
e
Using the wrong screw will reduce the holding force
required for proper installation possibly resulting in
personal injury or property damage.
Decide how you would like to install your DWST82800 48"
(122 cm) metal rail
1
before you begin.
1. DWST82800 metal rail
framed, masonry, or concrete wall. See Installing onto
Masonry/Concrete Walls to install on those surfaces.
2. DWST82800 metal rail
and metal studs.
WARNING: Before attempting to attach D
metal rail to metal studs and drywall consult your
local authority having jurisdiction "AHJ" for proper
fastening requirements. Improper installation can
cause personal injury and or property damage.
Single Section Installation
installing Onto Walls With Wood or Metal studs (Fig. B)
Position the DWST82800 metal rail
nOTE: If needed to fit your space, mark and cut the
DWST82800 metal rail
1
to a circular saw, miter saw, table saw, or jig saw.
1. Locate and mark wall studs
2. With the required tools and hardware close at hand,
position the DWST82800 metal rail
straighten using a level.
4
3
for mounting to
1
can be installed on a wood
1
may also be installed on drywall
1
in the desired location.
with a metal cutting blade attached
9
if installing over drywall.
1
onto the wall and
3. Screws
the ends of the DWST82800 metal rail
Spacing between the screws should be no more than
24" (609 mm).
4. If installing onto walls with wood studs, use the included
#10 screws
the wall.
5. If installing onto wall with metal studs, use #10 self-
tapping sheet metal screws (not included) to attach the
DWST82800 metal rail
through the top and bottom screw holes
wall studs
Repeat until DWST82800 metal rail
place, with two #10 screws
installing Onto Masonry/Concrete Walls
Prior to installing DWST82800 metal rail
concrete wall, waterproof the surface to prevent moisture.
DO nOT attempt to install the DWST82800 metal rail
using any type of masonry nail. Use #10 or 4.8 mm pan or
washer head masonry screws (not included).
1. With the required tools and hardware close at hand,
position DWST82800 metal rail
straighten using a level.
2. Mount the DWST82800 metal rail
masonry screws.
3. Place screws in the top and bottom screw holes
of the DWST82800 metal rail
between each mounting point is not less than
24" (609 mm). Always follow the masonry screw
manuafacturer instructions when installing.
4. Place screws in the screw holes
metal rail
mounting point is not less than 18" (457 mm). Always
follow the masonry screw manuafacturer instructions
when installing.
Inline Section Installation (Fig. C, D)
The end cap
DWST82800 48" (122 cm) metal rails
1. Install the first DWST82800 metal rail
Single Section Installation instructions.
WALT
e
2. Add the second DWST82800 metal rail
the previously installed DWST82800 48" (122 cm)
metal rail
3. Align the two end caps
as shown in Fig. D.
4. Install the second DWST82800 metal rail
in Single Section Installation instructions.
3
must be placed at least 1/2" (13 mm) from
3
to attach the DWST82800 metal rail
1
to the wall. Drive the screws
9
until snug against D
e
3
in each wall stud
1
1
. Ensure the distance
2
1
. Ensure the distance between each
4
is designed to connect two or more
1
.
4
and snap into them into place
1
section.
1
to
3
2
and into the
WALT metal rail
1
.
1
is held securly into
9
.
1
on a masonry or
1
on the wall and
1
to the wall using
2
of the DWST82800
1
together horizontally.
1
as described in
1
inline with
1
as described
Publicidad
