Hitachi Air home 800 XJ Serie Manual De Instrucciones página 10

FrostWash Operation
Is the total operation time of the air
conditioner beyond default setting when
the air-conditioner is operated for about 30
minutes and stopped?
The FrostWash be started that must to meet
with the follow conditions.
Accumulation time
FrostWash
Operation
The room
does not
temperature
start
The humidity in the
room
The outside
temperature
Does not change to non -automatic
"FrostWash"?
Does it happen after "time off"?
→Automatic "FrostWash" interval becomes
longer.
Within 60 minutes after the end of
"FrostWash", "FrostWash" is not operated for
product protection.
Noise
It is the sound that the internal machine is
occurred
inflated and contracted by the temperature
during
change and the fin of the heat exchanger is
FrostWash
frozen and thawed.
operation
Repeat for 1 second on and 1 second off for
10 seconds.
Because "FrostWash" can not work when
operating the "FrostWash" with remote
controller.
• The air conditioner is operating.
• Outside air temperature, room temperature
(Clean
and room humidity are not suitable for
Function
"FrostWash".
Lamp)
• It has not been over 60 minutes since the
blinks
end of "FrostWash".
Repeat for 4 seconds on and 1 second off for
15 seconds.
Because FrostWash has not been done for a
long time.
→ Operate the remote controller to operate
"FrostWash".
*Multi connection only available for manual
"FrostWash".
Indoor FrostWash Outdoor FrostWash
3.0 auto operation
auto operation
Accumulated Accumulated
operating hours of power supply of
the air conditioner the air conditioner
have exceeded have exceeded
about 42 hours about 60 days
About 10-32°C About 5-25°C
About 30-70% It does not request
About 1-43°C About 5-25°C
Mold Guard Function 2.0 Operation
(For single inverter only)
(Clean Function Lamp) on the indoor
During
unit lights up during Mold Guard Function
Mold Guard
2.0 operation. If Mold Guard Function 2.0
Function
operation stop at middle point, Clean Function
2.0
Lamp indicator will turn off.
If the air conditioner operation is stopped
after heating operation, Mold Guard Function
2.0 will not operate.
If the air conditioner has operated in cooling
and drying mode, including auto mode,
Mold Guard
for less than 10 minutes, the Mold Guard
Function
Function 2.0 operation will not start even if
2.0
the air conditioner is in off mode.
operation
does not
If operation of the air conditioner is stop by
start
OFF Timer, the Mold Guard Function 2.0 will
not operate.
If ON Timer is set and on time is within about
2 hours, the Mold Guard Function 2.0 will not
operate.
The horizontal deflector remain open.
Room temperature or humidity may rise.
Depending on situation, Mold Guard Function
2.0 will operate with Fan Mode.
When there would be the window near
indoor unit, the water might condense on the
Notes
window during Mold Guard Function 2.0. If
necessary, to cancel Mold Guard Function 2.0.
When after FrostWash operation, the water
inside the indoor unit evaporates, depending
on the room conditions, may emitted as
steam. But this is not a malfunction. If
necessary, to cancel Mold Guard Function 2.0.
Mold Guard Operation
(For Multi model will operate as Auto
Clean operation)
(Clean Function Lamp) on the indoor
During
unit lights up during Mold Guard operation.
Mold
If Mold Guard operation stop at middle point,
Guard
Clean Function Lamp indicator will turn off.
If the air conditioner operation is stopped
after heating operation, Mold Guard will not
operate.
If the air conditioner has operated in
cooling and drying mode, including auto
Mold Guard
mode, for less than 10 minutes, the Mold
operation
Guard operation will not start even if the air
does not
conditioner is in off mode.
start
If operation of the air conditioner is stop by
OFF Timer, the Mold Guard will not operate.
If ON Timer is set and on time is within about
2 hours, the Mold Guard will not operate.
-10-