Publicidad
Idiomas disponibles
Idiomas disponibles
OWNER'S MANUAL
FLYING INSECT TRAP
MODEL: DTl 2S0
Thank you for purchasing the
DYNATRAP® flying insect trap!
IMPORTANT SAFETY INSTRUCTIONS
WARNING, When using electric appliances, basic precautions should always be followed, including the
following:
- To disconnect, turn all controls lo the off ('O") position, then remove plug from outlet.
- Unplug from outlet when not
in
use and before servicing or cleaning.
- To reduce the risk of electrical shock, do not put appliance in
water
or other liquid.
- This appliance is provided with double
insulation.
Use only identical replacement
parts.
- Connect only to a circuit that is protected by a ground-fault circuit-interrupter (GFCI).
See instructions for Servicing of Double-Insulated
Appliances.
INSTRUCTIONS FOR DOUBLE-INSULATED, CORD-CONNECTED APPLIANCES:
In a double-insulated appliance, two systems of insulation ore provided instead of grounding. No
grounding
means is provided
on a double-insulated appliance, nor should a means for grounding be added to the appliance. Servicing of a double-insulated
appliance requires extreme core and knowledge of the system, and should be done only by qualified service
personnel.
Replacement ports for a double-insulated appliance must be identical to those ports in the
appliance.
IMPORTANT SAFETY INSTRUCTIONS
Please read these instructions before using the DYNATRAP® Insect Trap and keep for future reference.
l. Always turn unit off and disconnect plug before servicing, cleaning, or changing bulb.
2.
Do not position the unit near heat, gos, oil or other flammable
materials.
3. Place product out of reach from
children.
4. Never operate this product if it hos a damaged cord or plug, ii
it
is not working properly, ii
it
hos been dropped or
damaged, or if ii hos been dropped into
water.
5. This product is equipped with 2-conductor cord and 2-prong polarized plug as
a
safety feature. This plug will fit in a
polarized outlet only one way. If the plug does not fully lit in the outlet, then reverse the plug. If it still does not lit,
then contact a qualified
electrician.
To reduce the risk of electrical shock, only plug into a properly installed outlet.
Do not attempt to defeat this safety feature.
6.
Do not insert fingers or any foreign objects into the unit while ii is connected to an electrical outlet.
7.
Collected insects within the unit may contribute to fire, so clean insects from the unit
frequent~.
8. Do not clean this product with water
spray.
Do not place where ii con foll into water, or near flammable materials.
9.
Do not touch fan while in
motion.
l 0. Do not abuse cord--never carry or hong
unit
by cord or yank it to disconnect from receptacle. Keep cord away from heat,
oil, or sharp
edges.
11. Extension cords used with this product must be marked with suffix letters "W-A" and with a tog stating "Suitable for Use
with Outdoor Appliances".
12. Use only extension cords that hove plug and receptacles that match the product plug. Replace or repair damaged cords.
INSTALLATION & OPERATING INSTRUCTIONS
1.
Unpack unit. Save carton for off-season storage (if
needed).
2.
Assemble
stand:
Pull the cord tight through the poll stand. Turn base on its side and insert bottom
threaded plastic p iece into hose, connecting to the threaded plastic
cop.
Twist threaded plastic cop
clockwise to
tighten.
Complete installation by aligning upper ond lower support tube and inserting the
bor secttons. (For more detailed
instructions,
please refer to the assembly guide.)
3.
Plug cord into on outlet or UL listed extension cord as described in ' I MPORTANT SAFEIY
INSTRUCTIONS".
4.
Hold the Power switch on the side of the revolving rotation
door.
Twist the unit to the 'Power ON"
position.
When you hear a 'click", the machine is turned
on.
5.
For best catch results leave unit on at all
times,
except when cleaning or
servicing.
6.
Catch rote activity will be higher at night. For best catch results ii is recommended to keep the unit away from compettng light
sources.
Intended for household use
only.
7.
It is recommended to place the unit at least 10 to 20 feet away from where people will be sitting.
8.
This unit is all weather resistant- designed for outdoor use including rainy
conditions.
CLEANING
Frequent cleaning will prolong the life of the unit, ensure lire prevention and provide for more efficient operation.
1.
Be sure to clean the unit once per week
2.
To clean, hold the switch on the revolving rotation door and turn
ii
lo the ' P OWER OFF"
position.
After hearing the "click",
the machine is turned off. Unplug the unit.
3.
For weekly cleaning, remove the screw securing the retaining cage and then twist the cage
clockwise.
Remove any buildup from the inside
of the retaining cage and Ion with a brush
(included).
4.
For major cleaning, remove the four screws securing the Ion housing to the light housing. After removing the screws, gently pull the Ion
housing away from the light
housing.
Using a soft brush, remove dirt and debris from the light
housing.
Once the cleaning process hos
been completed, align the screw holes in the Ion housing with the screw holes in the lighting unit and tighten the screws to the base of
the lighting
unit.
5.
When replacing the retaining cage - DO NOT press/push against the screen windows.
REPLACING BULB
The light bulb life expectancy is approximately 3,000 hours (or about 4 months), and should be replaced regularly lo ensure opttmol UV
effectiveness. Even though the bulb's light may be visible to you, its ability to attract insects diminishes over
time.
1.
Turn power switch to "off"
position.
UNPLUG UNIT, and allow bulb lo cool before replacing.
2.
Remove the screw securing the retaining cage and then remove the retaining cage by lwisttng the cage
clockwise.
Turn the unit upside
down.
3.
Remove the lour screws securing the Ion housing to the light
housing.
After removing the screws, gently pull the Ion housing away from
the light housing. Using o soft brush, remove dirt and debris from the light
housing.
Once the cleaning process hos been completed,
untighten the screw securing the base of the light bulb to the light
housing.
Slide the metal bracket lo the
side.
Cover the bulb with a
cloth to protect your linger and
hand.
Grasp the bulb (with your hand and lingers protected by the cloth) and gently pull the bulb from
the socket.
4.
Remove any debris from the lamp socket with a brush before
inserting
the new
bulb.
Replace the metal plate over the base of the bulb
and tighten the retaining screw.
5.
Align the screw holes in the Ion housing with the screw holes
in
the lighttng unit and tighten the screws to the hose of the lighting
unit.
6.
Replace the retaining cage at the bottom of the unit.
Replacement Fluorescent Bulbs con be found at your local retailer or con be ordered directly from
~
IC.
by colling
1-877-403-TRAP (8727) or visiting
www.dynotrap.com.
HOW THE DYNATRAP® INSECT TRAP WORKS
F~ing insects are attracted to the unit by UV light and CO2 that is
generated by the photo-catalysis between the UV lamps and spe-
cial
Ti02
coating. The Ion then pulls the insects into the screened
base, trapping them until they dehydrate and
die.
The base con be
removed, allowing the
contents
to be periodical~ emptied into
the trash. The see-through screen shows the insects trapped in the
comportment, alerting you when the net needs to be
emptied.
TROUBLESHOOTING
Problem:
Possible cause:
Correction:
Bulb does not illuminate
1. No electrical power.
1. Check plug and receptacle and fuse or circuit breaker.
and fan does not
spin.
2.
Check to make sure power is switched to the
"on" position.
Bulb illuminates, but fan
1. Shorted
fan.
1. UNPLUG UNIT: Examine fan to see that it is free from
does not spin.
foreign material, dirt or build-up of dead
insects.
Cleon unit as in "CLEANING" section.
Fon spins, but bulb does
1. Bulb not seated
1. Check all sockets for proper bulb seating and alignment.
not illuminate.
properly.
2. Replace bulb if needed following instructions under
2.
Burnt out bulb.
"Replacing
Bulb".
LIMITED WARRANTY
DWNlft\lC.
warranties to the original purchaser that this product is free from defective materials and
workmanship. This warranty is limited to remedy any defective par! for a period of one year from dale of
original date of purchase. Retain your original receipt as proof of purchase. This warranty does not apply
to the light bulb, nor to, in our judgment, misuse or abuse. If this unit has been altered, no warranty is in
force. This warranty does not apply
if
this unit is purchased outside the United States, excluding Canada
and Mexico. In no case shall
DWtUft\l(.
be liable for any accidental, punitive, consequential, or any other
damages of any kind for breach of this or any other warranty, expressed or implied, whatsoever. Some
stales do not allow limitation on how long an implied warranty lasts, so the above limitation or exclusion
may not apply to you. This warranty gives you specific legal rights, and you may also have other rights
that vary from state to state.
PARTS
&
ACCESSORIES AVAILABLE
PART
DESCRIPTION
41050
7-Watt Replacement Fluorescent Bulb
(1
piece)
41051
Fon Blade Replacement
41052
Fon Blade and DC Motor Ultra-Long Life Replacement
41053
Retaining Cage
41061
Lorge Capacity Net (lo be used instead of the Retaining Cage, suitable for extra large catch performance)
l ~
\'IIC.
Dynamic Solutions Worldwide, LL(
12247 W
.
Fairview
Ave.
Milwaukee, WI 53226
Phone:
414-431-2819
Fox: 414-453-9975
Toll free: 1-877-403-TRAP (8727)
Or visit us online at www.dynotrop.com
EPA Est.
No.
08Bll9-CHN-001
EPA Est.
No.
OB7B37-Wl-001
©2012 DSW-LLC
SAVE THESE INSTRUCTIONS
lntertek
Publicidad
