Mitsubishi Electric PLFY-WL-NEMU-E Serie Manual De Instrucciones página 14

3. Operation
Manual vane angle
M-NET address
Function setting for unit
with vane fully open.
Return: RETURN
F1 F2 F3 F4
RETURN SELECT
MENU
HOLD
Manual vane angle
No communication
Check Unit state.
Return: RETURN
F1 F2 F3
■
Manual vane angle (Wireless remote controller)
Fig. 3-1
Fig. 3-2
en
Fig. 3-3
Display
Setting Step 1
Display
Setting Step 5
* The draft reduction can be set for only 1 vane.
The setting is enabled only for the last vane that was set.
12
2 After pressing the [F4] button,
wait approximately 15 seconds,
and then check the current state
of the air conditioner.
→ The vane is pointing downward.
→ This air conditioner is displayed
on the remote controller.
→ All outlets are closed. → Press
the [RETURN] button and continue
ON
the operation from the beginning.
OFF
→ The messages shown to the left
are displayed. → The target device
does not exist at this refrigerant
address.
• Press the [RETURN] button to
return to the initial screen.
3 Change the "M-NET address" to
the next number.
• Refer to step 1 to change the "M-
F4
NET address" and continue with
the confi rmation.
1 Going to the Manual vane setting
mode
Press the button.
(Start this operation from the status
of remote controller display turned
off .)
"FUNCTION" is lighted and "1"
blinks. (Fig. 3-1)
Press the button to select "2",
and then press the
2 Selecting the vane number (Fig.
3-2)
Press the buttons to select the
vane number A, and then press
A
the button.
3 Setting the vane angle (Fig. 3-3)
Press the buttons to select the
vane angle B.
B
Point the wireless remote controller
toward the receiver on the indoor
unit, and then press the
button.
4 P r e s s t h e
complete the settings.
Step 2 Step 3
No display
No setting Draft reduction*
3.6. 3D i-see Sensor setting
3.6.1 3D i-see Sensor setting
Main Main menu
Operation
F1 F2
RETURN SELECT
MENU
Operation
Vane·Louver·Vent. (Lossnay)
High power
Comfort
Main menu: RETURN
Cursor
F1 F2
RETURN SELECT
MENU
Comfort
Manual vane angle
3D i-See sensor
Setting display: SELECT
Cursor
button.
F1 F2
RETURN SELECT
MENU
3D i-See sensor
Air distribution
Energy saving option
Seasonal airflow
Setting display: SELECT
Cursor
F1 F2
RETURN SELECT
MENU
b u t t o n t o
Step 4
1 Select "Operation" from the Main
menu, and press the [SELECT/
HOLD] button.
F3 F4
ON
OFF
HOLD
2 Select "Comfort" from the
Operation menu, and press the
[SELECT/HOLD] button.
F3 F4
ON
OFF
HOLD
3 Select "3D i-See sensor" with the
[F1] or [F2] button, and press the
[SELECT/HOLD] button.
F3 F4
ON
OFF
HOLD
4 Select the desired menu with the
[F1] or [F2] button, and press the
[SELECT/HOLD] button.
• Air distribution
Select the airfl ow direction control
method when the airfl ow direction
is set to "Auto".
• Energy saving option
F3 F4
Operates the energy-save mode
ON
according to whether persons are
OFF
HOLD
detected in the room by the 3D
i-see Sensor.
• Seasonal airfl ow
When the thermostat turns off , the
fan and the vanes operate accord-
ing to the control settings.