Publicidad
Idiomas disponibles
Idiomas disponibles
Connecting
and Disconnecting
the Portable!Convertible
Dishwasher
The portable/convertible
dishwasher
must
be connected
to a faucet
and etectricM
outlet
each time
it is used,
Follow
directions
on this page
to properly
connect
dishwasher,
IMPORTANT:
Make
sure
door
is latched
before
moving
dishwasher.
Faucet
Adapter
Assembly
(Figure
A)
The power cot'd, faucet coupler
and hoses are located in a compartment
in
back of dishwasher.
A specia! adapter
must be installed
on faucet before
you
can connect
dishwasher
(Figure A)o
1. Remove faucet adapter' assembly from limramre
package.
2_ Unscrew existing sink faucet aerator.
3_ Check faucet spout
to see if threads are inside or outside.
• If threads are on inside of faucet spout, use both thick and thin rubber
washers,
• I£ threads
are on outside
of faucet spout, use thin rubber washer
only,
K faucet has no threads,
an adapter
kit with instructions
for
attachment
to a non-threaded
spout is available at most hardware
stores.
4. Assemble faucet spout as shown in Figure A Make sure the two brass
screens are located below the rubber washers,
:onnecting
the Portable
:aueee Adapter
Assembly
Figure B)
Electric
Shock
Hazard
Avoid fire hazard
or'
electrical
shock
Do
not use an adaptor
plug, extension
cord
or remove
grounding
prong from electrical
power coId Failure m
follow this warning
can cause serious
injur3,, fire or' death
rounding
type
atl receptacle/_
--.
_I
any circumstancesi
_iii!
(Do
not under
",
J cut, remove,
|
or bypass
|
"_ the groundlng
prongl
_. from
this plug.
J
Connecting
the
Portable/Conve_ible
Dishwasher
!,, Run water at faucet until it is
hot,
Turn off faucet.
2_ Pull hoses out of compartment.
3 Push collar down and slip faucet connector
onto faucet adapter'
(Figure
B). 4, When connector
snaps into place, release collar
5. Slowly t-urn on hot water all the way.
6. Piug power cord into grounded
outlet.
Disconnecting
the
Portable/Convertible
Dishwasher
1. When cycle has finished,
turn off hot water
2. Press red button on coupler' to release water pressure,
3 Press down on collar to release coupler,
4 Empty remaining
water from coupler
and return it to compartment.
5. Unplug power cord and ret_arn it to compartment,
IMPORTANT:
A sink spray hose
can burst
due to constant
water
pressure
while
in use. If your
spra9 hbse is in,tailed
on same water
l;me as the dishwasher,
it _s your
responsibility
to discor.mect
s_:'s
spray hose and to plug hole.
_:l_rq-4,-_l
C',-..,-.-_,-+.;.---
,r^_
_ _._
i_ t"
.....
'
{
,-........
, ,..,.,,,,,=,._,_,,, ,_,, a Pu_ L,_b,=/_oi_vertlb_e
Dishwasher
An electrical suppiy of I20 voits, 60 Hz, AC only, 15 amps is required_
For
)'our safer,!, the dishwasher
must be grounded
If there is a malfunction
or
breakdown,
grounding
will reduce risk of electrical shock. This dishwasher
has a power cord with a 3-prong grounding
plug It must be plu_ed_
into a
mating 3-prong grounding
type receptacle,
installed
and grounded
in
accordance
with the National Electrical
Code and any local codes and
ordinances.
To Convert.
a Portable
L4odel to a
Built-in
",'our portable
dishwasher
can be insta!ied under the counmr, A conversion
ldt is required
and is available at your Sears Service Center - Part No.
5303943 I39.
IMPORTANT:
Do not
use the portable
water
supply
hose
for permanent
installation,
It may
burst_
Complete
instructions
areha
the conversion
kit,,
............
Power supply
cord with 3_prong
grounding
plug
%\
{1
Publicidad
