Publicidad
Idiomas disponibles
Idiomas disponibles
DeckLift Lever
Found on your tractor's
right fender, the deck lift lever is used to
change the height of the cutting
deck. To use, move the lever to
the left, then place in the notch best suited for your application.
Ignition SwitchModule
_
ARNING!
Never
leave a running
machine
unattended.
Always disengage
PTO, set parking
brake, stop engine
and remove
key to
prevent
unintended
starting.
To start the engine,
insert the key
into the ignition
switch and turn
clockwise
to the START position.
@
Release the key into the NORMAL MOWING MODE position
once
the engine
has fired.
To stop the engine, turn the ignition
key counterclockwise
to the
STOP position.
CAUTION:
Prior to operating
the tractor,
refer to
both Safety Interlock
Switches and Starting The
Engine in the Operation
section of this manual for
detailed
instructions
regarding
the Ignition
Switch
Module and operating
the tractor in REVERSE
CAUTION MODE.
DrivePedal
The drive pedal is located
on the right side
of the tractor, along the running
board. Press
the drive pedal forward
to cause the tractor
to travel forward.
Ground
speed is also
controlled
with the drive pedal. The further
forward
that the pedal is pivoted,
the faster
the tractor
will travel. The pedal will return to
its original
position
when it's not pressed.
ShiftLever
The Shift Lever is used to shift the tractor's
drive
from Forward,
Reverse and Neutral.
|
SystemsindicatorMonitor/
HourMeter LCD
When the ignition
key is rotated out of
the STOP position
but not into the START
position,
the systems indicator
monitor
displays the battery's
output,
in volts, on
its LCD for approximately
five seconds,
after which it displays an hour glass and the
hours of tractor operation.
Once the tractor
is started, the monitor
continually
displays an hour glass and the
hours of tractor operation
on its LCD.
NOTE: Hours of tractor operation
are recorded
any time the
ignition
key is rotated
out of the STOP position,
regardless of
whether
the engine
is started.
The Indicator
Monitor
will also remind
the operator
of
maintenance
intervals
for changing
the engine oil. The LCD will
alternately
flash the recorded
hours, "CHG" and "OIL" for five
minutes,
after every 50 hours of recorded
operation
elapse. The
maintenance
interval
lasts for two hours (from 50-52,100-102,
150-152, etc.). The LCD will also flash as described
above for five
minutes
every time the tractor's engine
has been started
during
this maintenance
interval.
Before the interval
expires, change
the engine
oil as instructed
in the Maintenance
section of this
Operator's
Manual.
Brake
If the Brake light illuminates
when attempting
to start the
tractor's
engine, depress the brake pedal.
PT0(Blade Engage)
If the PTO light illuminates
when attempting
to start the tractor's
engine, move PTO lever into the disengaged
(OFF) position.
0il
It is normal for the Oil light to illuminate
while the engine
is
cranking
during
start-up,
but if it illuminate's
during
operation,
while the engine is running,
stop the tractor immediately
and
check the engine
oil level as instructed
in this Owner's
Manual.
Battery
It is normal for the Battery light to illuminate
while the engine
is
cranking
during
start-up,
but if it illuminate's
during
operation,
while the engine is running,
the battery
is in need of a charge
or the engine's
charging
system is not generating
sufficient
amperage.
Charge the battery
as instructed
in the Service
section
of this manual or have the charging
system checked
by
your Cub Cadet dealer.
SECTION 4
--
CONTROLS AND FEATURES
13
Publicidad
