Publicidad
Idiomas disponibles
Idiomas disponibles
3,
f
Pop open the protective
cap on the end of the oil drain
valve to expose the drain port. See Fig 6-1.
\\\
i
\\
/
/i
/
/
/
/
4,
5.
6,
7,
8.
Remove the oil fill cap/dipstick
from the oil fill tube.
Push the oil drain hose (packed with this manual) onto the
oil drain port. Route the opposite
end of the hose into an
appropriate
oil collection
container
with at least a 2.5 quart
capacity,
to collect the used oil.
The engine is equipped
with either a twist-and-pull
drain
port or a tabbed
drain port. If your engine
has the twist-
and-pull
drain go to step a. If your engine is equipped
with
the tabbed
drain go to step b.
a.
Turn the oil drain valve Y4-turn, then pull outward
to
begin draining
oil. After the oil has finished
draining,
push the end of the oil drain valve back in and turn
1A-turn to secure it back in place. Re-cap the end of
the oil drain valve to keep debris from entering
the
drain port.
b.
Pinch the tabs on the oil drain valve, then pull
outward
to begin draining
oil. After the oil has
finished
draining,
push the end of the oil drain valve
back in, until the tabs click into place. Re-cap the end
of the oil drain valve to keep debris from entering
the drain port.
Replace the oil filter as instructed
in the Kohler Owner's
Manual.
Refill the engine with new oil. Refer to the Kohler Owner's
Manual for information
regarding
the volume
and weight
of engine
oil
Air Cleaner
Service the pre-cleaner
and cartridge/air
cleaner element
as
instructed
in the Kohler Owner's
Manual.
SparkPlug
The spark plug should
be cleaned
and the gap reset once a
season. Refer to the Kohler Owner's
Manual for correct
plug type
and gap specifications.
Transmission
The transmission is sealed at the factory
and is maintenance-
free. The fluid level cannot
be checked
and the fluid cannot
be
changed.
Battery
CALIFORNIA PROPOSITION 65 WARNING!
Battery posts, terminals,
and related accessories
contain
lead and lead compounds,
chemicals
known
to the State of California
to cause cancer and
reproductive
harm. Wash hands after handling.
The battery
is sealed and is maintenance-free.
Acid levels cannot
be checked
and fluid can not be added.
Always keep the battery
cables and terminals
clean and
free of corrosive
build-up.
After cleaning
the battery
and terminals,
apply a light coat
of petroleum
jelly or grease to both terminals.
CAUTION:
If removing
the battery
for cleaning,
disconnect
the NEGATIVE (Black) wire from it's
terminal
first, followed
by the POSITIVE (Red) wire.
When re-installing
the battery, always connect
the
POSITIVE (Red) wire its terminal
first, followed
by the
NEGATIVE (Black) wire. Be certain that the wires are
connected
to the correct
terminals;
reversing
them
could result in serious damage
to your engine's
alternating
system.
(leaning the Tractor
Any fuel or oil spilled on the machine
should
be wiped
off
promptly.
Do NOT allow debris to accumulate
around the cooling
fins of the engine, the transmission's
cooling
fan or on any other
part of the machine,
especially
the belts and pulleys.
Smart Jet
TM
Your tractor's
deck is equipped
with a water port on its surface as
part of its deck wash system.
Use the Smart Jet
TM
to rinse grass clippings
from the deck's
underside
and prevent
the buildup
of corrosive
chemicals.
Complete
the following
steps AFTER EACH MOWING:
1.
Drive the tractor
to a level, clear spot on your lawn, near
enough
for your garden hose to reach.
CAUTION:
Make certain the tractor's
discharge
chute is directed
AWAY from your house, garage,
parked cars, etc.
2.
Disengage
the PTO (Blade Engage), set the parking
brake
and stop the engine.
3.
Thread the hose coupler
(packaged
with your tractor's
Operator's
Manual) onto the end of your garden hose.
SECTION 6 --
MAINTENANCE
& ADJUSTMENTS
Publicidad
