Publicidad
Idiomas disponibles
Idiomas disponibles
GENERAL
MAmNTENANCE
RECOHHENDATmONS
The pressure
washer
warranty
does not cover
items
that
have been
subjected
to operator
abuse or negligence.To
receive
furl vahe
from
the warranty,
the operator
must
maintain
the pressure washer as instructed
in this manual.
NOTE:
Should
you have questions
about
replacing
components
on your Troy-Bilt
pressure
washer_
please
call
m=888=6m m=6708 for assistance.
° Some adjustments will need to be made periodically to
properly
maintain your pressure washer.
* All maintenance in this manual and the engine owner's
manual should be made at least once each season.
° Once
a year you should
dean
or replace
the spark plug,
dean
or replace
the air filter
and check
the spray gun and
adjustable
nozzle extension
assembly
for wear.A
new spark
phg and dean air filter
assure proper
fuel=air mixture
and
help your
engine
run better
and Hast longer. Please refer to
your
engine owner's
manual for more details.
* If equipped
with
inflatable
tires,
keep the air pressure
at
the value marked
on the tire or within
I S and 40 psi.
Before
Each
Use
I.
Check engine oil level.
2.
Check water inlet screen for damage,
3.
Check indine filter for damage,
4.
Check high pressure hose for leaks,
S.
Check chemical injection
hose and filter for damage,
6.
Check spray gun and adjustable nozzle extension
assembly for leaks,
7.
Rinse out garden hose to flush out debris,
PRESSU
RE WASH
ER
MAmNTENANCE
Ched<
and
aean
Inlet
Screen
Examine
the screen
on the water
inlet. Clean
it if the
screen
is dogged
or replace
it if screen
is damaged.
_h
Pressure
Hose
The high pressure
hose can develop
leaks from
wear,
kinking,
or abuse. Inspect
the hose each time
before
using
it. Check
for cuts, leaks, abrasions
or bulging
of cover,
damage
or movement
of couplings.
If any of these
conditions
exist,
replace
the hose immediately.
WARNING
NEVER repair high pressure hose. Replace it,
Replacement
hose rating MUST exceed maximum
pressure
raring of unit.
ection
Hose
Examine
the filter
on the detergent
tube
and dean
if
clo£__ed.The
tube
should
fit tightly
on the barbed
fitting.
Examine
the tube
for
leaks or tears.
Replace
the filter
or
tube
if either is damaged.
aeanin_ection
Hose
If you used the chemical
injection
hose, you must
flush it
with
clean water
before
stopping
the engine.
I.
Place chemical
injection
hose
in a bucket
full of clean
water.
2.
Slide adjustable
nozzle
forward
to low
pressure
position.
Flush for 1:2 minutes,
3.
mMPORTANT:
Simply
shutting
OFF engine
will not
release
pressure
in the system.
When
the
engine
has
shut down,
squeeze
the
trigger on the
spray
gun
to
relieve the pressure
in the hose.
Check
Gun
and Adjustable
Nozzle
Examine
the hose connection
to the spray gun and make
sure
it is secure.Test
the trigger
by pressing
it and making
sure
it"springs
back"
into
place when
you release
it. Put
the
trigger
lock
in the
ON
position
and
test
the
trigger.
You should
not be able to press the tri&ser.
Check
In-Line
Filter
Refer to Figure
13 and service
the indine
filter
if it
becomes
clo&$ed,
as follows:
Nozzle Extension
O-rir
Publicidad
