Descargar Imprimir esta página

Anker Solix A5500 Manual página 8

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 10
Installation
Read the instructions before installation. Damage caused by failure to follow instructions is not covered by warranty.
Section
Permission
• When installing a solar panel on a balcony, make sure it can extend beyond the balcony railing.
• The solar PV system is grid-tied. Check with your local authorities to see if installation is allowed, and
the process may require approval before or after installation.
Installation
• Install or remove the PV system with caution. There must be no people or property beneath the work
area as it is a danger zone.
• During installation or removal, we recommend that at least two people work together. Ensure the solar
panel is firmly secured before tightening the hose clamps.
• The Mounting Auxiliary Rope must be connected to the balcony railing before the solar panel can be mounted.
• It is recommended to carry solar panels with at least two people. During installation, bumping or falling
will damage the glass surface of the solar panel.
• All installations should follow local electrical codes. Further protection of AC wiring from inverters
should be provided and may be required by local and national wiring regulations. This protection may
include Residual Current Devices, Earth Fault Monitors, and Circuit Breakers. This product may cause
AC current with a DC component. If a residual current-operated protective device (RCD) or a monitoring
device (RCM) is used for protection in case of direct or indirect contact, only an RCD or RCM of Type B is
allowed on the AC side of this product.
• There should be no changes made inside the microinverter other than the cable connectors.
Maintenance
• Never disconnect the solar panel from the microinverter without turning off the AC power. Before
removing the Schuko plug, the PV and AC connectors should not be disconnected under load.
• The brackets are only designed to withstand winds of level 8 (Gale, 39 - 46mph, which may break twigs
and small branches or make walking challenging). Additional protective measures may be necessary
during extremely windy weather, such as temporarily removing solar panels.
• If the brackets are rusted, deformed, or have any other conditions that affect their strength, it is
necessary to take protective measures immediately. These measures may include rust prevention,
reinforcement, or replacement.
• Do not damage the solar panel with sharp objects as it is made of glass.
• To receive maximum sunlight, solar panels should never be covered when in use.
• Never disconnect the DC wire connectors under load.
• Do not touch the heat dissipation surface of the microinverter. Please be aware of high temperatures
and keep them away from children.
• Do not attempt to repair the microinverter. It does not contain any user-serviceable parts. If
troubleshooting methods fail, please contact an authorized service agent.
Notice
CE RED Declaration of Conformity (For Microinverter)
This product complies with the radio interference requirements of the European Community. Hereby, Anker Innovations Limited
declares that the radio equipment is in compliance with Directive 2014/53/EU. The full text of the EU Declaration of Conformity is
available at the following website: https://www.anker.com
Bluetooth maximum output power: 18.18 dBm (For EU)
Bluetooth frequency band: 2.4G band (2.402GHz - 2.480GHz)
Wi-Fi maximum output power: 19.86 dBm (For EU)
Wi-Fi frequency band: 2.4G band (2.412GHz - 2.472GHz)
This symbol indicates that this product shall not be treated as household waste. Instead, it shall be handed over to
the applicable collection point for the recycling of electrical and electronic equipment.
11 EN
Notice
Specifications
Microinverter
Model
Recommended PV Module Power (STC) Range
Peak Power Tracking Voltage
Operating Voltage Range
Input Data (DC)
Maximum Input Voltage
Maximum Input Current
Isc PV
Maximum Continuous Output Power
Nominal Output Voltage / Range (1)
Output Data (AC)
Nominal Output Current
Nominal Output Frequency / Range (1)
Power Factor
Peak Efficiency
Efficiency
Nominal MPPT Efficiency
Night Power Consumption
Operating Ambient Temperature Range (2)
Storage Temperature Range
Dimensions (W × H × D)
Mechanical Data
Weight
DC Connector Type
Cooling
Enclosure Environmental Rating
Wire Size
AC Extension Cable
Cable Length
(Optional)
Plug Type
Communication (Inverter To ECU)
Features
Isolation Design
Energy Management
Compliances
Safety and Grid Compliances
(1) Nominal voltage / frequency range can be extended beyond nominal if required by the utility.
(2) The microinverter may enter Power Degrade mode if there is poor ventilation and heat dissipation in the installation
environment.
A5143
(300 Wp-730 Wp+)*2
28V-45V
16V-60V
60V
20A × 2
25A × 2
799VA
230V/184-253V
3.5A
50Hz/47.5Hz-51.5Hz
0.99
97.30%
99.50%
20mW
-40 °C to 65 °C
-40 °C to 85 °C
263mm × 218mm × 36.5mm
2.8kg
Stäubli MC4 PV-ADBP4-S2&ADSP4-S2
Natural Convection - No Fans
IP67
1mm²
5M (Default)
Schuko
Built-in Wi-Fi and Bluetooth
High Frequency Transformers, Galvanically Isolated
Energy Management Analysis (EMA) system
EN 62109-1/-2;
EN 50549-1;
DIN V VDE V 0126-1-1; VFR;UTE C15-712-1;
CEI 0-21;
UNE 217002;
VDE-AR-N 4105
EN 12

Publicidad

loading

Este manual también es adecuado para:

Solix a5507