General Safety; Safety Rules - Triton TRA001 Instrucciones De Uso Y De Seguridad

General Safety

WARNING: For Your Own Safety Read Instruction Manual before Operating
1. Wear eye protection.
2. Be sure keyed washer is directly under spindle nut and spindle nut is tight OR Always use
both spindle nuts and make sure spindle nuts are tight.
3. Feed workpiece against rotation of cutter
4. Do not use awkward hand positions.
5. Keep fingers away from revolving cutter – use fixtures when necessary.
6. Use overhead guard when adjustable fence is not in place.

Safety Rules

1. KEEP GUARDS IN PLACE and in working order.
2. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and
adjusting wrenches are removed from tool before turning it on.
3. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.
4. DON'T USE IN DANGEROUS ENVIRONMENT. Don't use power tools in damp or wet locations,
or expose them to rain. Keep work area well lighted.
5. KEEP CHILDREN AWAY. All visitors should be kept safe distance from work area.
6. MAKE WORKSHOP KID PROOF with padlocks, master switches, or by removing starter keys.
7. DON'T FORCE TOOL. It will do the job better and safer at the rate for which it was designed.
8. USE RIGHT TOOL. Don't force tool or attachment to do a job for which it was not designed.
9. USE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When
using an extension cord, be sure to use one heavy enough to carry the current your product
will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and
overheating. Table A shows the correct size to use depending on cord length and nameplate
ampere rating. If in doubt, use the next heavier gage. The smaller the gage number, the
heavier the cord.
10. WEAR PROPER APPAREL Do not wear loose clothing, gloves, neckties, rings, bracelets, or
other jewelry which may get caught in moving parts. Nonslip footwear is recommended.
Wear protective hair covering to contain long hair.
11. ALWAYS USE SAFETY GLASSES. Also use face or dust mask if cutting operation is dusty.
Everyday eyeglasses only have impact resistant lenses, they are NOT safety glasses.
12. SECURE WORK. Use clamps or a vise to hold work when practical. It's safer than using
your hand and it frees both hands to operate tool.
13. DON'T OVERREACH. Keep proper footing and balance at all times.
14. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance.
Follow instructions for lubricating and changing accessories.
15. DISCONNECT TOOLS before servicing; when changing accessories, such as blades, bits,
cutters, and the like.
16. REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is in off position
before plugging in.
17. USE RECOMMENDED ACCESSORIES. Consult the owner's manual for recommended
accessories. The use of improper accessories may cause risk of injury to persons.
18. NEVER STAND ON TOOL Serious injury could occur if the tool is tipped or if the cutting tool
is unintentionally contacted.
19. CHECK DAMAGED PARTS. Before further use of the too., a guard or other part that is
damaged should be carefully checked to determine that it will operate properly and
perform its intended function - check for alignment of moving parts, binding of moving
parts, breakage of parts, mounting, and any other conditions that may affect its operation.
A guard or other part that is damaged should be properly repaired or replaced.
20. DIRECTION OF FEED. Feed work into a blade or cutter against the direction of rotation of
the blade or cutter only.
21. NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF. Don't leave tool until it
comes to a complete stop.
Table A
Ampere Rating Volts
120
240
More Not More
Than Than
0 6
6 10
10 12
12 16
Total length of cord in feet
25 50 100 150
50 100 200 300
Minimum gage for cord
18 16 16 14
18 16 14 12
16 16 14 12
14 12 Not Recommended
Additional Safety for Routers
• Hold the power tool by insulated gripping surfaces only, because the cutter may
contact its own cord. Cutting a "live" wire may make exposed metal parts of the power
tool "live" and could give the operator an electric shock.
• Use clamps or another practical way to secure and support the workpiece to a
stable platform. Holding the work by your hand or against the body leaves it unstable
and may lead to loss of control.
• If the replacement of the supply cord is necessary, this has to be done by the
manufacturer or his agent in order to avoid a safety hazard.
• It is strongly recommended that the tool always be supplied via a residual current
device with a rated residual current of 30 mA or less.
a) Use safety equipment including safety goggles or shield, ear protection, dust mask
and protective clothing including safety gloves
b)Cloths, cord, string etc should never be left around the work area
c) Ensure the mains supply voltage is the same as the tool rating plate voltage
d) Ensure any cable extensions used with this tool are in a safe electrical condition, and
have the correct ampere rating for the tool
e) Completely unwind cable drum extensions to avoid potential overheating
f) Use appropriate detectors to determine if utility cables or pipes are below the
surface of the work area. Consult utility companies for assistance if necessary. Contact
with electric cables can lead to electric shock and fire. Damaging a gas pipe can lead to
explosion. Contact with water lines can lead to major property damage
g) Ensure embedded objects such as nails and screws have been removed from the
workpiece before commencing operation
h) Handle router bits with care as they can be extremely sharp
i) Before use, check the bit carefully for signs of damage or cracks. Replace damaged or
cracked bits immediately
j) Ensure router cutters/bits are sharp and maintained correctly. Dull cutting edges can
lead to uncontrolled situations including stalling, increased heat and possible injury
k) ALWAYS use both handles and maintain a firm grip on the router before proceeding
with any work
l) Keep handles and gripping surfaces dry, clean and free of oil and grease to ensure the
tool can be securely held in use
m) Before using the tool to make a cut, switch on and let it run for a while. Vibration
could indicate an improperly installed bit
n) Take notice of the direction of rotation of the bit and the direction of feed
o) Keep your hands away from the routing area and router bit cutter. Hold the auxiliary
handle or an insulated gripping surface with your second hand
p) NEVER start the router while the cutter is touching the workpiece
q) Ensure the plunge spring is always fitted when using hand-held
r) Ensure the cutter has completely stopped before plunging to the collet lock position
s) The maximum speed of the router bit/cutter must be at least as high as the maximum
speed of the power tool
t) Parts of the router bits may become hot during operation. Do not handle immediately
after use to avoid risk of burns
u) Do not allow parts to come into contact with combustible materials
v) The shank size of the router cutter/bit must be matched to the exact same size collet
fitted to the router. Incorrectly fitted router cutter/bits will rotate irregularly and have
increased vibration that could lead to loss of control
w) DO NOT press the spindle lock button, or attempt to switch the tool into bit change
mode while the router is operating
x) Keep pressure constant while cutting into the workpiece, allowing the router bit
cutter to dictate the speed of cut. DO NOT force the tool and overload the motor
y) Ensure rating labels and safety warnings on the tool remain clear to read and are
replaced if marked or damaged
z) When operating the router, be prepared for the router bit cutter stalling in the
workpiece and causing loss of control. Always ensure the router is firmly held and the
on/off switch is immediately released in such circumstances
• After switching on the router, check the router bit is rotating evenly (not 'wobbling')
and there is no additional vibration due to the router bit being incorrectly fitted.
Operating the router with an incorrectly fitted router bit can lead to loss of control and
severe injury
• EXTREME care must be taken when using cutters with a diameter greater than
2" (50mm). Use very slow feed rates and/or multiple shallow cuts to avoid overloading
the motor
• ALWAYS switch off and wait until the bit has come to a complete standstill before
removing the machine from the workpiece
• Disconnect from the power supply before carrying out any adjustment, servicing
or maintenance
WARNING!
GB
5