Publicidad
Idiomas disponibles
Idiomas disponibles
ckback
Safety Features
WARNING: The following features are included on your saw
to help reduce the hazard of kickback; however such features
wilt not totally eliminate this dangerous reaction. As a chain saw user
do not rely only on safety devices. You must follow all safety
precautions, instructions, and maintenance in this manual to help
avoid kickback and other forces which can result in serious injury.
• Reduced-Kickback
Guide Bar, designed with a small radius tip
which reduces the size of the kickback danger zone on bar tip. A
reduced - kickback guide bar is one which has been demonstrated to
significantly reduce the number and seriousness of kickbacks when
tested in accordance with safety requirements for electric chain saws.
• Low=Kickback
Chain, designed with a contoured depth gauge and
guard link which deflect kickback force and allow wood to gradually
ride into the cutter. A low-kickback chain is a chain which has met
kickback performance requirements of ANSI B175.1-1991.
• Do not operate chain saw while in a tree, on a ladder, on a
scaffold,
or from any unstable surface.
• Hold tool by insulated gripping
surfaces
when performing an
operation
where the cutting
tool may contact hidden wiring.
Contact with a "live" wire will make exposed metal parts of the tool
"live" and shock the operator.
• Do not attempt operations
beyond your capacity
or
experience.
Read thoroughly and understandcompletely
all
instructions in this manual.
• Before you start chain saw, make sure saw chain is not
contacting any object.
• Do not operate a chain saw with one hand! Serious injury
to the operator,
helpers, or bystanders
may result from one
handed operation. A chain saw is intended for two-handed use only.
• Keep the handles dry, clean, and free of oil or grease.
Do not allow dirt, debris, or sawdust to build up on the motor
or outside air vents.
• Stop the chain saw before setting it down.
• Do not cut vines and/or small under brush.
• Use extreme caution when cutting
smatl size brush and
saplings
because slender material may catch the saw chain and
!_be whipped toward you or pull you off balance.
WARNING:
Some dust created by power sanding, sawing,
grinding, drilling, and other construction activities contains chemicals
known to the State of California to cause cancer, birth defects or
other reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
crystalline silica from bricks and cement and other masonry
products, and
• arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending on how often
you do this type of work. To reduce your exposure to these
chemicals: work in a well ventilated area, and work with approved
safety equipment, such as those dust masks that are specially
designed to filter out microscopic particles.
• Avoid prolonged contact with dust from power sanding,
sawing, grinding,
drilling,
and other construction
activities.
Wear protective clothing
and wash exposed
areas with soap
and water. Allowing dust to get into your mouth, eyes, or lay on the
_Nkin maypromote
absorption of harmful chemicals.
ARNING: Use of this tool can generate and/or disburse dust,
which may cause serious and permanent respiratory or other injury.
Always use NIOSH/OSHA approved respiratory protection appropriate for
the dust exposure. Direct particles away from face and body.
SAVE THESE
INSTRUCTIONS
Symbols
The label on your tool may include the following symbols.
V. ................................ volts
Hz..............................
herlz
min.............................
minutes
- - -. ........................
directcurrent
@ ..............................
ClassIConstructbn
(grounded)
[] ..............................
ClassIIConstructbn
(doubleinsulated)
........................
Read instruction
manualbeforeuse
..............................
Useproper eyeprotedion
A.............. amperes
W............. watts
,_ .......... attemabhg current
no............ no loadspeed
8. ........... earthingterminal
z_.......... safetyalert s ymbd
.../min or rpm...revduiions o r
recfprocation perminute
............ Useproper
respiratory p rotectlbn
0 ........... Useproper
heatingprotection
Publicidad
