Electronic Programmer - Cardin Elettronica GL Serie Manual Del Usuario

ELECTRONIC PROGRAMMER

Electronic programmer for a direct current motor with an incorporated
radio receiver card, which allows the memorisation of 300 user codes
(see "Remote Control" on page 16).
The "rolling code" type decoder uses 433,92 MHz. series transmitters.
The travel speed is electronically controlled, starting slowly and increasing
in speed; the speed is reduced as it nears the travel limit so as to enable
a controlled smooth stop (if deceleration hasn't been excluded during
programming).
Programming is carried out using two buttons and allows you to configure
the system, set the length of the deceleration stage and set the work and
pause times.
The intervention of the anticrush/antidrag sensor during the closing and
opening stages causes travel direction inversion (if automatic reclosing
has been abilitated). If activated towards the end of the movement (almost
closed) it will act as a travel limit.
ELECTRICAL CONNECTION
• Open the "Standard wiring diagram". To make it easier to follow the
instructions the diagram has been placed on the inside of the last page
of this manual.
ELECTRONIC CARD DESCRIPTION (fig. 9)
B1 Signal buzzer "via radio" mode
CN1 Secondary Faston connection 24 Vac logic card power supply
CN2 Secondary Faston connection motor circuit power supply
V0: 0 Vac, V1: 22 Vac, V2: 30 Vac
CN3 Battery Faston connection
D1
Seven segment display
F1 1,6A delayed action fuse (230V power supply protection)
F2 1A rapid action fuse (24V circuit protection)
F3 10A rapid action fuse (motor power supply protection)
J1
Enable transmitter memorisation via radio
L1 LED power on
L2 LED transmitter code programming
L3 LED manual operation mode
L4 LED inverting photocells activated
L5
LED opening travel limit
L6 LED closing travel limit
L7
LED blocking button activated
L8 LED stop photocell activated
M1
Memory module
P1 Programming button (PROG)
P2 Selection button (SEL)
P3 Transmitter code memorization button (MEMO)
P4 Transmitter code cancellation button (DEL)
R1 Radio frequency module, 433,92 MHz for S449 transmitters
LP
Flashing warning lights
LS Indicator light
FCA
Opening travel limit
FCC Closing travel limit
FTC-RX Photocell receiver
FTC-Tx Photocell transmitter
PS Safety buffer pressure switch
SEL
Selector switch
TB Blocking button
ANS400
External antenna
Before connecting the appliance make sure that the voltage and
frequency rated on the data plate conform to those of the mains
supply. A multiple pole trip switch with at least 3mm between
the contacts must be installed between the unit and the mains
supply.
• Connect the control and security device wires.
• Connect the power supply cable to the device.
• Do not use cables with aluminium conductors; do not solder the ends of
cables which are to be inserted into the binding posts; use cables which
are marked "T min 85°C" and are resistant to atmospheric agents.
• The terminal wires must be positioned in such a way that both the wire
and the insulating sheath are tightly fastened. Where possible use the
supplied cable clamp. The cable entry hole "11" (fig.3, pag.11) must be
sealed using a rubber cable clamp or similar.
Terminal board connection
1-2 Common for all inputs and outputs
3 24 Vac 7W in output, powering external devices
4-5 Common for all inputs and outputs
6 24 Vac 10W in output warning lights
(intermittent or continuous activation)
7 TD (contact N.O.) Dynamic button input "Open-Close"
8 TB (contact N.C.) Blocking button input
(The opening of this contact interrupts the cycle until a new move-
ment command is given)
9-17 Common for all inputs and outputs
10 FCC (contact N.C.) closing travel limit switch
FCA (contact N.C.) opening travel limit switch
11
12 FTC_I (contact N.C.) Safety and control devices in input
(these photocells invert the travel direction when an obstruction
is detected).
The opening of this contact will provoke a travel direction inversion
during closure due to the cutting in of the safety device
13 FTC _ S (contact N.C.) Safety and control devices in input. (stop photo-
electric cells). The opening of this contact will block all movement, until
the obstruction has been removed and the pause time has elapsed,
due to the safety device cutting in, the door will then continue moving
in the closing direction (only with automatic reclosing enabled).
14 TC (contact normally open) Closing button in input
15 TA (contact normally open) Opening button in input
16 TAL (contact normally open) limited opening button
Indicator light 24 Vac 3W
18
19-20 230Vac 60Hz output powering the toroidal transformer
21-22 Power supply 230Vac 60 Hz
23-24 230Vac 40W Courtesy light in output
25 Programmer earthing wire
26 Motor earth outputs (not used)
27 Mass for radio receiver antenna
28 Pole for radio receiver antenna (if an external antenna is fitted use
a coaxial type cable RG58 with an impedance of 50Ω)
NOTE: ALL UNUSED NC CONTACTS MUST BE JUMPED
Switch on the power and make sure that the red indicator LEDS are in the
following condition:
- L1
Power on LED
- L2 Transmitter code programming LED
- L3 Manual operation mode LED
- L4 Safety LED for the inverting photoelectric cells "FTC_I"
- L5
Opening direction travel limit LED "FCA"
- L6 Closing direction travel limit LED "FCC"
- L7 Safety LED for the blocking button "TB"
- L8 Safety LED for the stop photoelectric cells "FTC_S"
* The LEDs are "ON" if the relative security device is inactive (depends on
the position of the door). Check that the activation of the safety devices
switches the corresponding LEDS off.
If the red power on LED doesn't light up check the condition of the fuses
"F1" and "F2" and the power cable connection between binding posts
"21" and "22" (fig. 9).
If one or more of the safety LEDS do not light up check the contacts
of the relative security devices and check that the unused safety device
contacts have been bridged.
12
on
off
off
on
on*
on*
on
on