Remote Control - Cardin Elettronica GL Serie Manual Del Usuario

REMOTE CONTROL

The motor can be remotely activated using a transmitter: only the sequential
function is available "open-block-close-block" and this may be activated
from any of the available channels.
For this reason for each transmitter enabled you need only use one of the
available channels.
S449 RADIO CONTROLS
Memory module
This is extractable, furnished with a non volatile EEPROM type memory
and contains the transmitter codes and allows you to memorise up to 300
codes (300 channel buttons). The programmed codes are maintained in
this module even in the absence of power.
Attention! Before memorising the transmitters for the first time
remember to cancel the entire memory content.
If the electronic card has to be replaced due to failure, the
module can be extracted from it and inserted into the new card.
Make sure that the module is orientated in the direction shown
in fig. 9 detail A.
Signal LEDs "L2" (fig. 9):
Flashing quickly: cancels a single code
Flashing slowly: memorises a single code
Permanently lit: memory full.
TRANSMITTER CODE MANAGEMENT
A) Memorising a channel (using the associated transmitter)
B) Cancelling a channel (using the associated transmitter)
C) Cancelling all codes in memory
D) Memorising ulterior channels via radio (without having to open the
box in which the receiver is housed)
A) Memorising a channel (fig. 9)
1. Press and hold down button "P3" MEMO: the LED "L2" will flash slowly.
2. At the same time activate the transmitter which is to be memorised.
3. Hold down button "P3" MEMO until LED "L2" starts to flash again.
4. Release the button: The LED will continue to flash.
5. Activate the transmitter again (same transmitter, same channel; if the
channel is different or it is a different transmitter the memorisation attempt
will abort without success)
6. End of memorisation: The LED "L2" will remain lit for 2 seconds, indicat-
ing that the transmitter has been correctly memorised.
Note: It is not possible to memorise a code which is already in memory: if
you attempt this, the LED will switch off when you activate the transmitter
(point 2). Only after releasing the button "P3" MEMO will you be able to
continue the memorising procedure.
If after activating the transmitter for the first time you wait for more than
fifteen seconds without activating the transmitter a second time the memo-
risation attempt will abort without success.
B) Cancelling a channel (fig. 9)
1. Press and hold down button "P4" DELETE: the LED "L2" will flash quickly.
2. Activate the transmitter channel which is to be cancelled.
3. The LED "L2" will remain lit for 2 seconds, indicating that the transmitter
has been cancelled.
Note: If the user that you wish to cancel is not in memory, The LED will stop
flashing; Only after releasing the button "P4" will you be able to continue
the cancellation procedure.
For both the memorisation and cancellation procedures, if the button is
released before activating the transmitter the procedure will abort.
C) Cancelling all user codes from memory (fig. 9)
1. Keep both buttons pressed down ("P3+P4") for more than 4 seconds
2. LED "L2" will remain lit during the entire cancellation time (about 8 sec.).
3. LED "L2" switches off when the cancellation procedure has terminated.
Note: When the memory is almost full the time required to search for a user
code could take up to 1 second from when the command was received.
If led "L2" remains alight memory is completely full. To memorise a new
transmitter you will first have to cancel a code from memory.
D) Memorising ulterior channels via radio
• Memorisation can be activated by radio (without opening the receiver
container) if jumper "J1" has been inserted (fig. 9).
1. Make sure that the jumper "J1" has been inserted (fig. 9).
2. Using a transmitter, in which at least one chan-
nel button "A, B, C or D" has already been
memorised in the receiver, press the button
in the transmitter as shown in the figure.
Note: all the receivers within range when the
channel button is pressed (and which have at least one of the transmitter
channel buttons memorised) will activate their signal buzzer "B1" (fig. 9).
3. Press one of the channel buttons on the same transmitter. The receiv-
ers which do not contain that channel code will sound a five-second
long "beep" and will then disactivate. The receivers which contain the
channel code will sound a one-second long "beep" and will enter the
"programming mode".
4. Press the previously chosen channel buttons on the transmitter which
you wish to memorise; the receiver will sound 2 "beeps" of half a second
each after which the receiver will be ready to receive another code.
5. To leave the programming mode wait for "3" seconds without pressing
any buttons. The receiver will sound a five-second long "beep" and will
then exit the programming mode.
• When the memory is entirely occupied the buzzer will sound 10 rapid
"beeps" and will automatically leave the "programming via radio" mode.
Led "L2" will remain lit on the receiver. The same signal is given each
time you try to enter "programming via radio" when the memory is full.
CONNECTING THE 433,92 MHz MODULE ANTENNA
The receiver is supplied with its own antenna which consists of a piece
of rigid wire 170 mm in length.
In alternative it is possible to connect an ANS400 tuned antenna using a
coaxial cable RG58 (impedance 50Ω) with a maximum length of 15 m.
16
Description : MEMORIZZAZIONE CODICE TX-RX
Drawing number : DM0531
Product Code : RCQ449100
P.J.Heath Date : 13-04-2001
Draft :
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401