Manual Mode - Nemox crea Serie Instrucciones Para El Uso

(HACCP or equivalent).
•For the preparation of ice creams and sorbets,
do not introduce more than 1.5kg of mixture, in
order to allow for proper volume increase while
mixing.
•For the preparation of Granitas, the maximum
recommended amount is 1.3kg. mixed with
the paddle provided. It can process up to
1.8kg. of Granita using the special Granita
paddle that can be purchased separately.
•It is recommended to pour the mixture at a
temperature between +10°C and +20°C.
Higher temperatures may also considerably
increase the processing time.
DIRECTIONS FOR USE
•Check that the voltage indicated on the data
plate corresponds to the local network. Insert
the power plug into the power outlet and
operate the main switch (10); the light will
indicate the presence of voltage.
The electronic board will run an initialization
check, triggering all the LEDs on the control
panel in sequence.
•Check that discharge fitting (7) is close with
the special plug (9) until i is fully locked.
•Insert the mixing paddle (5) in the pot, turning it
clockwise until it is positioned in the bottom of
the pot.
•Tighten the locking ring (4) to the bottom so
that the mixing paddle is securely attached.
•Pour the previously prepared mixture.
•Close the lid (3).

MANUAL MODE

•Start the cooling system by pressing the
button (1); the LED (1a) will light up.
IMPORTANT: if the machine is turned off due to
sudden and temporary suspension of power
supply or incorrect operation using the power
keys of the refrigerant, wait a few minutes
before restarting.
•Press button (2) to start the paddle; the LED
(2a) lights up, the production cycle begins.
The preparation time varies depending on the
quantity, initial temperature of the mixture,
product type (creamed, sorbet or Granita) and
ambient temperature.
IMPORTANT: The movement of the paddle is
entirely independent of the cooling system. A
safety device stops the movement of the paddle
when the lid is lifted.
If the lid remains raised for prolonged periods,
the cooling system will continue to operate.
English
Consequently, when the lid is lowered again the
paddle may not start or stop due to the
excessive consistency of the mixture. In this
case, the electronic control will permanently
stop the paddle and LED (2a) will flash to
indicate the fault.
If the preparation is not yet complete, turn off the
compressor by pressing the button (1) and the
paddle via the button (2), wait until the mixture
becomes softer and restart production.
•According to the recipe and the amount of
ingredients used, average production time is
15/20 minutes.
•Through the opening (3a) on the lid, you can
add additional ingredients (e.g. to make ripple
ice cream during the last preparation phase).
•The paddle rotation speed is adjustable by
means of the knob (8). Select the desired
speed according to the preparation to be
obtained. It is recommended to use low
speeds in the preparation of classic Italian
gelato, Granita and sorbet. While higher
speeds are suitable for the preparation of soft
Italian gelato.
•When the preparation has reached the desired
consistency, turn off the cooling system by
pressing button (1) and stop the paddle by
pressing button (2). To easily remove the
preparation from the pot, remove the mixing
paddle (5) by loosening the appropriate
locking ring (4).
MANUAL START OF THE PRESERVATION
CYCLE
•Should it become necessary to start the
preservation cycle manually, you can do this at
any time. Keep paddle button (2) and
c o m p r e s s o r b u t t o n ( 1 ) p r e s s e d
simultaneously for 3 seconds. The machine
will immediately switch to preservation cycle
related to the classic Italian gelato production
program. The LED (12a) will turn on.
•Should you need to run a preservation cycle
related to a different production program,
before switching from manual mode to
preservation mode, select the desired
production program (see section "CHANGING
THE PRESERVATION CYCLE").
AUTOMATIC MODE
The GELATO 6K CREA
programs which automate the production and
preservation process.
•Follow the steps described in the section
machine has a series of
7