Bavaria BBC 52/2 Manual De Instrucciones Original página 20

5.2. Adjusting the cutting height
•
Slip the shoulder strap (15) over your left
shoulder.
•
To establish the optimum length of the har-
ness, you should then make a few swinging
movements without starting the engine (Fig.
11a).
Warning! Always use the strap when working
with the equipment. Attach the strap as soon as
you have started the engine and it is running in
idle mode. Switch off the engine before you take
off the carrying strap.
6. Before starting the equipment
Check the equipment for the following each time
before use:
•
That there are no leaks in the fuel system.
•
That the equipment is in perfect condition and
that the safety devices and cutting devices
are complete.
•
That all screws are securely fastened.
•
That all moving parts move smoothly.
6.1 Fuel and oil
Recommended fuels
Use only a mixture of unleaded petrol and special
2-stroke engine oil. Mix the fuel mixture as indica-
ted on the fuel mixing table.
Important: Do not use a fuel mixture which has
been stored for longer than 90 days.
Important: Never use 2-stroke oil with a recom-
mended mixing ratio of 100:1. The manufacturer's
warranty will be voided in case of engine damage
due to inadequate lubrication.
Important: Only use containers designed and ap-
proved for the purpose to transport and store fuel.
Pour the correct quantities of petrol and 2-stroke
oil into the mixing bottle (see scale printed on the
bottle). Then shake the bottle well.
6.2 Fuel mixture table
Mixing procedure: 40 parts petrol to 1 part oil
Petrol
1 liter
5 liters
Anl_BBC_52_2_SPK7.indb 20 Anl_BBC_52_2_SPK7.indb 20
GB
2-stroke oil
25 ml
125 ml
- 20 -
7. Operation
Please note that the statutory regulations gover-
ning noise abatement may diff er from town to
town.
Before starting up the equipment remove the pro-
tective caps from the cutting blade (18).
7.1 Starting the engine when cold
Fill the tank with an adequate amount of petrol/oil
mix. See „Fuel and oil".
1. Set the equipment down on a hard, level sur-
face.
2. Press the fuel pump (primer) (Fig. 14a/Item
39) ten times.
3. Set the On/Off switch (Fig. 1/Item 9) to „I".
4. Secure the throttle lever. To do this, press the
throttle lever lock (Fig. 1/Item 12) and then the
throttle lever (Fig. 1/Item 11), and secure the
throttle lever by pressing the lock (Fig. 1/Item
10) simultaneously.
5. Set the choke lever (Fig. 1/Item 6) to ON.
6. Hold the equipment securely and pull out the
starter cable (Fig. 1/Item 4) until you feel it
begin to resist. Then tug sharply on the starter
cable 4 times. The equipment should start.
Note: Never allow the starter line to snap
back. This may result in damage.
Warning: Since the throttle lever is secured,
the cutting tool will start to operate when
the engine is started. Once the engine has
started, move the choke lever immediately to
OFF and allow the equipment to warm up for
approx. 3 seconds. Then release the throttle
lever by simply actuating it (the engine then
returns to running in idle mode).
7. If the engine does not start up, repeat steps
4-6 above.
Please note: If the engine does not start up even
after several attempts, read the Engine trouble-
shooting section.
Please note: Always pull out the starter cable in a
straight line. If it is pulled out at an angle, friction
will occur on the eyelet. As a result of this friction,
the cable will become frayed and will wear faster.
Always hold the starter handle when the cable
retracts.
Never allow the cable to snap back when it has
been pulled out.
29.08.2019 10:13:03 29.08.2019 10:13:03