cecotec BOLERO AGUAZERO 6500 C Manual De Instrucciones página 33

ENGLISH
Connecting the water inlet hose. Fig. 3
- Connect the cold-water supply hose to a 3/4 inch/19 mm threaded connector and make
sure it is securely in place.
- If the water pipes are new or have not been used for a long period of time, let the water run
to ensure that it is clean and free of impurities. If this precaution is not taken, there is a risk
that the water inlet will be blocked, and the appliance will be damaged.
Connecting the drain hose. Fig. 4
Insert the drain hose into a drainpipe. When the hose is attached, the height of the outlet is
between 0.5~1 metre.
Note
- Please note that the drain hose cannot be disconnected, so the outlet must be fixed and
as close as possible to the dishwasher. The drain hose must be at a maximum distance of
1~1.5 metres from the dishwasher.
- In case the distance is longer, this will affect the draining process of the dishwasher,
causing too much wastewater to accumulate in the hose, thus affecting the performance
of the dishwasher.
Electrical connections
- Before plugging the appliance into the mains, make sure that:
- The plug is earthed and complies with current regulations.
- The socket can withstand the maximum load of the appliance, which is indicated on the
rating plate on the inside of the door (see description of the appliance).
- The supply voltage is within the values indicated on the rating plate inside the door.
- The socket is compatible with the plug of the appliance. If not, have the plug replaced by an
authorised technician. Do not use an extension cord or multiple sockets.
- Once the appliance has been installed, the power cable and the power socket must be
easily accessible.
- The cable must not be bent or compressed.
- If the power cable is damaged, it must be replaced by the manufacturer or the official
Cecotec Technical Support Service to avoid any potential risk.
- Cecotec will not be held responsible for any incidents that occur if these rules are not
followed.
Advice regarding the first wash cycle
- Once the appliance has been installed, just before starting the first wash cycle, fill the rinse
aid dispenser completely and add, approximately, 2.0 kg of salt (see below for details on
how). Water may overflow: this is normal and not a cause for concern.
- It is also normal for the LOW SALT indicator light to keep flashing for a few cycles after the
salt has been loaded.
64
Bolero Aguazero 6500 C/ Inox C/ Dark C
Positioning the appliance
Position the appliance in the desired location. The back of the dishwasher must rest against the
wall behind it, and the sides, in the cabinets or adjacent walls. The dishwasher is equipped with
water supply and drain hoses which can be positioned on the right or left for easy installation.
Levelling the device
Once the appliance has been positioned, adjust the feet (screwing them in or out) to adjust
the height of the dishwasher and level it. In any case, the appliance must not be tilted by more
than 2°.
NOTE: the maximum height adjustment of the feet is 20 mm.
How to drain excess water from hoses
If the outside drain hose is higher than the lowest point of the dishwasher, it is possible that
the wastewater cannot be completely discharged through the drain pump, so it is necessary
to remove the hose and place it horizontally on the floor in order to discharge the water from
the hose into a container.
Water outlet
Install the drain hose. The drain hose must be correctly placed to prevent water leakage. Make
sure the water inlet hose is not twisted or crushed.
Syphon installation
The connection must be between 50 cm (minimum) and 110 cm (maximum) above the bottom
of the dishwasher. The drain hose must be secured with a hose clamp.
4. BEFORE USING THE DISHWASHER
Before switching on the appliance, check:
1. If the dishwasher is level and fixed.
2. If the inlet valve is open.
3. If there are leaks in the conductor connections.
If the cables are properly connected.
4.
5. If the power is on.
6. If the inlet and drain hoses are screwed on.
7. If all packaging material and printed material have been removed from the dishwasher.
Then, before using the dishwasher for the first time:
A. Set the water softener.
B. Pour 500 mI of water into the salt dispenser and then fill it with dishwashing salt.
Fill the rinse aid dispenser.
C.
D. Set the detergent.
ENGLISH
65
Bolero Aguazero 6500 C/ Inox C/ Dark C