Audio Settings - JVC KD-T915BTS Manual De Instrucciones

Audio Settings

1
Press and hold .
2
Turn the volume knob to select an item (see the following table), then
press the knob.
3
Repeat step 2 until the desired item is selected/activated or follow the
instructions stated on the selected item.
4
Press to exit.
To return to the previous setting item, press
[EQ SETTING]
[PRESET EQ] Selects a preset equalizer suitable to the music genre.
• Select [USER] to use the settings made in [EASY EQ] or [PRO EQ].
[FLAT]/[DRVN 3]/[DRVN 2]/[DRVN 1]/[HARD ROCK]/[HIP HOP]/[JAZZ]/
[POP]/[R&B]/[USER]/[CLASSICAL]
Drive equalizer ([DRVN 3]/[DRVN 2]/[DRVN 1]) boosts specific frequencies
in the audio signal to reduce the noise heard from outside the car or running
noise of the tyres.
[EASY EQ] Adjusts your own sound settings.
• The settings are stored to [USER] in [PRESET EQ].
• The settings made may affect the current settings of [PRO EQ].
[SUB.W SP]*1*2: [00] to [+06]
[SUB.W]*1*3: [–50] to [+10]
[BASS]: [LVL–09] to [LVL+09]
[MID]: [LVL–09] to [LVL+09]
[TRE]: [LVL–09] to [LVL+09]
[PRO EQ]
.
[AUDIO CONTROL]
Default: [XX]
[BASS BOOST]
[LOUDNESS]
[SUB.W
LEVEL]*1
(Default: [+03]
[SUBWOOFER
[00]
SET]*3
[LVL 00]
[LVL 00]
*1, *2, *3: (see page 30)
[LVL 00])
Adjusts your own sound settings for each source.
• The settings are stored to [USER] in [PRESET EQ].
• The settings made may affect the current settings of [EASY EQ].
[62.5HZ]
[LEVEL –09] to [LEVEL +09] ([LEVEL 00]): Adjusts the level to memorize for each source.
(Before making an adjustment, select the source you want to adjust.)
[ON]: Turns on the extended bass. ; [OFF]: Cancels.
[100HZ]/[160HZ]/[250HZ]/[400HZ]/[630HZ]/[1KHZ]/[1.6KHZ]/[2.5KHZ]/[4KHZ]/
[6.3KHZ]/[10KHZ]/[16KHZ]
[LEVEL –09] to [LEVEL +09] ([LEVEL 00]): Adjusts the level to memorize for each source.
(Before making an adjustment, select the source you want to adjust.)
[Q FACTOR] [1.35]/[1.50]/[2.00]: Adjust the quality factor.
[LEVEL +01] to [LEVEL +05]: Selects your preferred bass boost level. ;
[OFF]: Cancels.
[LEVEL 01]/[LEVEL 02]: Boosts low or high frequencies to produce a well-
balanced sound at low volume. ; [OFF]: Cancels.
[SPK-OUT]*2 (Not applicable when 3-way crossover is selected.)
[SUB.W 00] to [SUB.W +06] ([SUB.W +03]): Adjusts
the output level of the subwoofer connected via speaker
lead. (Page 46)
[PRE-OUT]*3 [SUB.W –50] to [SUB.W +10] ([SUB.W 00]): Adjusts
the output level of the subwoofer connected to the
lineout terminals (SW or REAR/SW) through an external
amplifier. (Page 47)
[ON]: Turns on the subwoofer output. ; [OFF]: Cancels.
29
ENGLISH