Publicidad
Idiomas disponibles
Idiomas disponibles
n el producto.
®
{GNICION
0
ABIERTA
_TO
NTAMIENTO
kSEGADORA
{GROS DE
_DtENTES
_s de seguddad)
,RGA DE LA BARRA
DE ENGANCHE
evita,
nO se evita,
Yes.
_ose evita,
:leradas.
'mbolo de aviso,
r da6os
al
_ligro que,
e, leslones
Ata, puede
to danos
-I}
1_ ¸
BELT INSTALLATION
-
1.
Install new belt from tractor
rear to
front, over the steering
plate (H) and
above clutch brake pedal shaft (J).
2.
Putl belt toward
front of tractor
and roll
belt around
electric
clutch and onto
engine pulley (G).
3.
Pull belt toward
rear of tractor. Carefully
work
belt
down
around
transmission
cooling fan and onto the input pulley (F).
Be sure
belt is inside
the belt keeper.
4.
Install belt on centerspan
idler (E).
5.
Install belt through
stationary
idler (C)
and clutching
idler (D).
6.
Reinstall
anti-rotation
link (B) on right
side of tractor. Tighten
securely.
7.
Reconnect
clutch
harness
(A).
8.
Make sure belt is in all pulley grooves
and inside all belt guides
and keepers.
9.
Install mower
(See "TO INSTALL
MOWER"
in this section
of manual).
TO CHECK
BRAKE
If tractor requires
more than five (5) feet to
stop at highest
speed in highest
gear on a
level, dry concrete
or paved surface, then
brake must be serviced.
You may also check brake by:
1.
Park tractor
on a level, dry concrete
or
paved surface,
depress
brake pedal all
the way down and engage parking brake.
2,
Disengage
transmission
by placing
freewheel
control
in "transmission
dis-
engaged"
position.
Pull freewheel
con-
trol out and into the slot and release so
it is held in the disengaged
position.
The rear wheels
must lock and skid
when you try to manually
push the tractor
forward.
If the rear wheels
rotate, then the
brake needs to be serviced.
Contact a
Sears
or other qualified
service
center.
FRONT
WHEEL
TOE.IN/CAMBER
Your new tractor front wheel toe-in and cam-
ber is set at the factory
and is normal. The
front wheel toe-in and camber are not adjust-
able.
If damage
has occurred
to affect the
factory set frontwheel
toe-in or camber, con-
tact a Sears or other qualified
service center.
TO REMOVE
WHEEL
FOR REPAIRS
1.
Block up axle securely.
2.
Remove
axle cover,
retaining
ring and
washers
to allow
wheel
removal
(rear
wheels have a square key - Do not lose).
3.
Repair tire and reassemble.
NOTE: On rearwheels
only: align grooves in
rear wheel hub and axle. Insert square key.
4.
Replace
washers
and snap retaining
ring securely
in axle groove.
5.
Replace
axle cover.
NOTE:
To seal tire punctures
and prevent
fiat tires due to slow leaks, purchase
and
use tire sealant from Sears. Tire sealant
also prevents
tire dry rot and corrosion.
Washers
Retaining
Ring
Axle Cover
I
_----'_Square Key (Rear
Wheel Only)
TO START ENGINE WITH A WEAK BATTERY
_WARNING:
Lead-acid
batteries
gen-
erate explosive
gases.
Keep sparks, flame
and smoking
materials
away from bat-
teries.
Always
wear eye protection
when
around
batteries.
if your battery' is too weak to start the
engine,
it should
be recharged.
(See "BAT-
TERY"
in the MAINTENANCE
section
of
this manual).
If "jumper
cables"
are used for emergency
starting,
follow this procedure:
27
Publicidad
