Teac T-H300 Manual Del Usuario página 10

RDS Display
1. Select the FM broadcasting.
RDS can be received only in FM.
2. Select the RDS broadcasting by use of
the tuning mode button and the
tuning/select control. Then RDS will light
up in the upper side of the display. And
the related data, if received, will be
displayed in the type of received data
(PTY, RT, TP, TA).
3. RDS
1) The default of the RDS mode is PS.
2) Press the RDS mode button.
Each time you press the button briefly
(0.5 sec or less), the modes will change
as follows regardless of the current
mode.
[> PS—> PTY—+ RT —> TA > CT 1]
3) PS mode
- When you select PS with the RDS mode
button, "PS" will blink for about 4
seconds.
- After 4 seconds, PS or a station name
entered by manual file will be displayed.
4) PTY mode
- When you select PTY with the RDS mode
button, PTY will blink for about 4
seconds. After 4 seconds, the type of
received PTY will be displayed.
- If there is no PTY data among received
broadcasting, RDS mode will be
switched to PS mode automatically.
5) RT mode
- When you select RT with the RDS mode
button, "RT" will blink for about 4
seconds. After 4 seconds, the data of
received RT will be displayed.
If there is no RT data among received
broadcasting, RDS mode will be
automatically switched to PS mode.
6) TA mode (TP Search Function)
- When you select TA by use of the RDS
mode button, "TA" will blink for about 4
seconds. After 4 seconds, TP received
broadcasting will be searched with FM
frequency increasing in 100 kHz steps.
If TP received broadcasting is searched,
the increase in frequency will stop and it
is asked whether TA will be received or
not.
- When TA is received, the input selector
of the amplifier will be automatically
switched to the tuner.
When TA has finished, the input selector
of the amplifier will automatically return
to the previous position.
If TP and TA turn off while you are
receiving TA, the tuner will search TA
broadcasting again with FM frequency
increasing in 100 kHz steps.
7) CT mode
- When you select CT with the RDS mode
button, "CT" will blink for about 4
seconds. After 4 seconds, the clock time
together with the frequency will be
displayed.
PTY Search
- Press the RDS mode button for longer
than 1.5 second.
Then "SEARCH" will be shown in the
display.
Select the desired PTY mode by using
the tuning/select control.
- If you press the next button, the PTY
mode will blink in the clock display.
- Searching will start when you turn the
tuning/select control.
- When the PTY mode that you have
selected is searched, searching will
stop and the PTY mode will be
displayed.
- If there is no program in the PTY mode
you have selected, searching will stop
at the frequency started.
"CT can be received regardless of
whichever RDS mode the tuner is set
to.
eon
-10-
Specifications
FM Section
Frequency Range:
87.50 MHz to 108.00 MHz (50 kHz
steps) (Europe)
(S/N 30 dB EMF) : 3.0uV
Total Harmonic Distortion
Mono: 0.15%
Signal-to-Noise Ratio
Mono: 70dB
Stereo: 65dB
Frequency Response: 20Hz to 15kHz
Image Rejection: 70dB
AM Suppression: 55dB
Stereo Separation(1kHz): 40dB
AM Section
Frequency Range:
522kHz to 1,620kHz (9kHz steps)
Sensitivity (S/N 20dB): 55dB
Signal-to-N Ri 40dB
Total Harmonic Distortion: 1.0%
Image Rejection: 35dB
General
Power Requirement: 230V, 50Hz
Power Consumption: 6W
Dimensions(W x H x D): 215 x 93 x 305 mm
Weight(Net): 2.3kg
Standard Accessories:
Remote Control Cord x 1
Signal Input/Output Cord x 1
AM loop antenna x1
Lead-type FM antenna x 1
* Improvements may result in specification
or feature changes without notice.
* Photos and illustrations may differ slightly
from production models.