Synergic Curves Screen - Selco Genesis 3000 MTE Instrucciones De Uso

501 Info
Allows the display of a set of information related to the
system.
502 Alarm queue
Allows the intervention of an alarm to be indicated and
provides the most important indications for the solution
of any problem encountered.
(Consult the "Alarms screen" section).
551 Lock/unlock
Allows the locking of the panel controls and the inser-
tion of a protection code (consult the "Lock/unlock"
section).
552 Buzzer tone
Permits adjustment of the buzzer tone.
Minimum Off, Maximum 10, Default 10
553 Contrast
Permits adjustment of the display contrast.
Minimum -20, Maximum +20, Default 0
601 Regulation step
Allows the regulation of a parameter with a step that
can be personalised by the operator.
Minimum 1, Maximum Imax, Default 1
602 External parameter CH1, CH2, CH3, CH4
Allows the management of external parameter (mini-
mum value, maximum value, default value, parameter
selected).
(Consult the "External controls management" section).
606 U/D torch
Allows the management of the external parameter
(CH1) (parameter selected).
705 Circuit resistance calibration
Lets you calibrate the system.
Press the encoder knob to access parameter 705.
Place the tip of the wire guide in electrical contact with
the work piece.
Press and hold the torch trigger for at least 1 s.
751 Current reading
Allow the real value of the welding current to be dis-
played.
Allows the welding current display method to be set
(consult the "Interface personalisation" section).
752 Voltage reading
Allows the real value of the welding voltage to be dis-
played.
Allows the welding voltage display method to be set
(consult the "Interface personalisation" section).
800 Read filter (guard thresholds)
Lets you filter current and voltage readings. Minimum 1,
Maximum 5, Default 1
801 Guard limits
Allows the setting of the warning limits and of the guard
limits.
Allows the accurate control of the various welding
phases (consult the "Guard limits" section).
802 Starting filter
Allows the control of the guard limits to be enabled with
an adjustable delay in relation to the arc striking.
Makes it possible to filter the striking phase (consult the
"Guard limits" section).
803 Output filter
Makes it possible to disenable the control of the guard
limits in advance of the natural closing of the weld.
Makes it possible to filter the extinction phase (consult
the "Guard limits" section).
44

3.6 Synergic curves screen

1 General
Allows the selection of the required welding method.
Manual welding method
Allows the manual setting and regulation of
each individual welding parameter (MIG/
MAG).
Synergic welding method
Makes it possible to use a series of pre-settings
(synergic curves) available in the memory of the
system.
The changing and correction of the initial set-
tings proposed by the system is allowed.
1
Press key 4 ( ) to cancel the operation.
2/3
Lets you select:
- type of filler material
- gas type
4
Lets you select:
- wire diameter
5
- Type of filler material
- Gas type
6 Wire diameter
7 Header
(See the "Main screen" section).
NO PROGRAM
Indicates that the selected synergic program is not avail-
able or is not consistent with the other system settings.
2 Synergic curves
MIG/MAG - Pulsed MIG
0,8
G3/4 Si1 CO 2
1
G3/4 Si1 Ar 18%CO 2
5
CrNi Ar 2%CO 2
9
AlMg Ar
17
AlSi Ar
21
Al Ar
25
CuAl Ar
29
CuSi Ar
33
Basic FCW Ar 18%CO 2
/
Rutil FCW Ar 18%CO 2
/
Metal FCW Ar 18%CO 2
/
CrNi FCW Ar 18%CO 2
/
No Program
/
Ø (mm)
1.0 1.2 1.6
2 3 /
6 7 /
10 11 /
18 19 /
22 23 /
26 27 /
30 31 /
34 35 /
/ 45 47
/ 48 50
/ 51 53
/ 54 56
/ / /