Bosch GDS 18V-1600 HC Professional Manual Original página 15

Bluetooth® in aircraft. Avoid using the product near
your body for extended periods.
The Bluetooth® word mark and logos are registered trade-
marks owned by Bluetooth SIG, Inc. Any use of such
marks by Robert Bosch Power Tools GmbH is under li-
cense.
Application tools can become hot during operation.
u
There is a risk of burns when changing the application
tool. Use protective gloves to remove the application
tool.
WARNING
Only use the coin cells listed in this operating manual.
u
Do not use any other coin cells or other forms of electrical
power supply.
Stop using the power tool if the battery compartment
u
cover no longer closes; remove the coin cell and have
the power tool repaired.
Battery is hazardous and is to be kept
away from children (whether the battery
is new or used). Battery can cause severe
or fatal injuries in 2 hours or less if it is
swallowed or placed inside any part of
the body. Medical attention should be
sought immediately if it is suspected the
battery has been swallowed or placed in-
side any part of the body.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended Use
The machine is intended for driving in and loosening screws
and bolts as well as for tightening and loosening nuts within
the respective range of dimension.
®
With the Bluetooth Low Energy Module GCY 42 inserted,
power tool data and settings can be transferred between the
power tool and a mobile device by means of Bluetooth
less technology.
Product features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Tool holder
(2) Rotational direction switch
(3) Bluetooth® Low Energy Module cover GCY 42
(4) Ladder clip
Bosch Power Tools
(5) Rechargeable battery
(6) Battery release button
(7) User interface
(8) On/off switch
(9) Handle (insulated gripping surface)
(10) Application tool (e.g. impact socket)
User interface
(11) Status indicator for power tool
(12) Mode indicator
(13) Mode button
(14) Worklight
(15) Speed button
(16) Speed preselection indicator
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical Data
Cordless Impact Wrench
Article number
Rated voltage
A)
No-load speed
– Setting 1
– Setting 2
– Setting 3
A)
Impact rate
– Setting 1
– Setting 2
– Setting 3
A)
Torque
– Setting 1
– Setting 2
– Setting 3
Max. tightening torque
Max. loosening torque
Machine screw diameter
Tool holder
Weight according to
®
wire-
EPTA-Procedure 01:2014
Recommended ambient tem-
perature during charging
Permitted ambient temperat-
ure during operation and dur-
ing storage
Compatible rechargeable
batteries
English | 15
a)
a)
a)
GDS 18V-1600 HC
3 601 JM1 0..
V=
–1
min 0–800
–1
min 0–1 300
–1
min 0–1 750
–1
min 0–1 550
–1
min 0–2 200
–1
min 0–2 350
Nm 0–600
Nm 0–1 100
Nm 0–1 600
A)
Nm 1 600
A)
Nm 2 200
mm M16–M33
kg 3.6–4.6
B)
°C 0 to +35
°C –20 to +50
GBA 18V...
ProCORE18V...
1 609 92A 8EA | (08.09.2023)
18
∎ ¾"