Stanley STDC001LB Manual Del Usuario página 10

10 • ENGLISH
c. Disconnect the plug from the power source and/or
the battery pack from the power tool before
making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main
voltage corresponds to the voltage on the rating
plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
Stanley Service Center or an equally qualified
person in order to avoid damage or injury. If the
power cord is replaced by an equally qualified
person, but not authorized by Stanley, the
warranty will not be valid.
7. Labels on tool
The label on your tool may include the following
symbols:
W ........
Read
Instructions
min .....
Manual
Use Eye
Protection
Use Ear
Protection
n .......
0
V ........ Volts
A ........ Amperes
Hz ....... Hertz
Watts
....
minutes
....
..... Alternating
Current
.../min..
..... Direct
Current
No-Load
....
Speed
...... Class II
Construction
FEATURES (Fig. A)
This tool includes some or all of the following features.
1. Variable speed switch
2. Forward/reverse slider
3. Chuck
4. Torque adjustment collar
5. Battery
6. Belt clip
7. LED work light
8. Speed selector
9. Magnetic bit holder
Fig. B
10. Charger
11. Charging indicator
ADDITIONAL POWER TOOL SAFETY WARNINGS
Warning! Additional safety warnings for drills and
impact drills.
f Wear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
f Use auxiliary handles supplied with the tool. Loss
of control can cause personal injury.
f Hold power tool by insulated gripping surfaces
when performing an operation where the cutting
accessory may contact hidden wiring. Cutting
accessory contacting a "live" wire may make exposed
metal parts of the power tool "live" and could give the
operator an electric shock.
f Hold power tool by insulated gripping surfaces
when performing an operation where the fastener
may contact hidden wiring. Fasteners contacting
a "live" wire may make exposed metal parts of
the power tool "live" and could give the operator an
electric shock.
f Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body leaves
it unstable and may lead to loss of control.
f Before drilling into walls, floors or cellings, check for
the location of wiring and pipes.
f Avoid touching the tip of a drill bit just after drilling,
as it may be hot.
Earthing
f This tool is not intended for use by persons (including
Terminal
children) with reduced physical, sensory or mental
Safety Alert
capabilities, or lack of experience and knowledge,
Symbol
unless they have been given supervision or instruction
Revolutions
or Recipro-
concerning use of the appliance by a person responsible
cation per
for their safety. Children should be supervised to
minute
ensure that they do not play with the appliance.
The charger
is intended
f The intended use is described in this instruction
for indoor
use only.
manual. The use of any accessory or attachment
or performance of any operation with this tool other
than those recom- mended in this instruction manual