Publicidad
Idiomas disponibles
Idiomas disponibles
Operating instructions
Special safety features
Attention: This machine has the following 3 safety switches.
The machine only be started with all the safety switches are at
the proper positions.
• Bowl position safety switch: The machine can be started up
once the bowl is positioned at the correct position.
• Bowl guard safety switch: The machine can only be started up
once the bowl guard is in the closed position.
• Bowl lift up handle safety switch: The machine can only be
started up once the bowl lift up handle is located in the up-
wards position.
• Do not wear loose fitting clothing such as scarf, etc and long
hair should be tied up and keep away from the moving parts.
To avoid serious personal injury:
• DO NOT operate the machine without reading the instruction
manual.
• ALWAYS STOP the machine by pressing RED " " button and
unplug from electrical power supply before cleaning, mainte-
nance, repair or changing any attachments.
• ALWAYS keep hands, hair and loose clothing away from the
moving parts.
About the bowl guard
Note: When bowl guard is open or not properly closed in lock
position, the machine will not operate.
1. To open the bowl guard, hold the bowl guard handle and
rotate it clockwise. To close the bowl guard, hold the bowl
guard handle and rotate it anti-clockwise.
2. When the bowl guard handle is lined up at the right side of
the machine, the bowl guard is in the is in the rocked posi-
tion and ready for operation.
Install the bowl to the machine
Note: Install the bowl BEFORE fixing the attachments. Use the
supplied bowl only.
1. Lower the bowl by pulling the bowl lift-up lever downwards
until it stops. So that the bowl cradle is in a lower position.
2. Place the bowl carefully and slowly using the bowl handles
at 2 sides and
i. With the locking pin into the hole at the middle of the
bowl cradle and
ii. Secure the bowl by pull each bowl clamp forward until
the bowl is locked tight. (Fig.17 on page 16)
Install different attachments (Flat beater, Dough hook or
Whisk) to the machine
Note: It is more convenient and easier to install the attach-
ments prior to adding the ingredients into the bowl.
1. Rotate the bowl guard clockwise gently with the bowl guard
handle, so that it is in the open position.
2. CAUTION! Use excessive force to open or close the bowl
guard may damage the safety lock micro switch. Be careful
when open or close the bowl guard.
3. Slide the attachments (Flat beater, Dough hook or Whisk)
slowly upwards onto the planetary shaft fitting the shaft pin
through the slot in the attachments.
4. Rotate the attachments to secure it onto the planetary
shaft.
Pouring and mixing ingredients
Note: Follow the "Operating tips" table in this manual. Over-
loading will lead to overflow or damage to the machine.
IMPORTANT: Make sure the speed control lever is set at the
"dough hook" position.
1. Add all the appropriate ingredients into the bowl.
2. Lift upwards the bowl lift lever until the bowl locks into the
position.
3. Rotate the bowl guard anti-clockwise and locks into the
position.
ATTENTION: The machine will not start if the bowl guard is
open / not closed properly or the bowl is at the lower position.
Set the speed, attachment & start up the machine
1. Select the appropriate speed by lifting or lowering the speed
control lever. Three fixed speeds are available for different
attachments:
Rotation speed
Type of ingredient
Dough hook
Heavy: Mixing pizza, bread, pasta
(Low)
Flat beater
Medium: 2nd stage of mixing for donut dough,
(Medium)
etc.
Whisk (High)
Light: Whipping cream, egg whites, meringue.
IMPORTANT: ALWAYS follow the recommended attachment
used and speed setting according to the capacity table and indi-
cation next to the speed control lever.
ATTENTION: Be careful about the risk of dust and flour escape
when slitting of bags of ingredient into bowl. Wear protective
mask or glasses if necessary.
2. After that, press the GREEN " " button to switch ON the
machine. Press RED " " button to STOP the machine.
The machine will rotate in clockwise direction for item
222843 whereas and anti-clockwise direction for 222836.
(Fig.18 on page 16)
3. CAUTION! ALWAYS STOP the machine BEFORE changing
speeds. Failure to do so may damage the internal gear con-
struction.
4. To change the speed during the operation:
i. Press the RED " " button to STOP the machine.
ii. Unplug the machine and change the attachment. [See
==> part c].
iii. Change the speed by raising or lowering the speed con-
trol lever with the correct attachment.
iv. Press the GREEN " " button to restart the machine.
RESET the safety cut-out (Hi-limiter or thermal
cut-out)
(Fig.19 on page 16)
• Please note that the RESET button is equipped with a protec-
tive cap to avoid overheat.
• Disconnect the appliance from the power supply.
• Allow the appliance to completely cool down.
• Unscrew the protective cap of the RESET button.
• Press the RESET button of the Hi-limiter (thermal cut-out).
You should hear a click sound.
• Screw back the protective cap on the RESET button.
• Connect to the power supply and you can use it again.
GB
25
Publicidad
