Gardol GEK-E 2240 Manual De Instrucciones Original página 24

ries of any kind caused as a result of this.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
4. Technical data
Mains voltage: ................... 220-240 V ~ 50/60 Hz
Power rating: ........................................... 2200 W
Idling speed: ......................................... 7800 rpm
Cutter rail length: .................................... 406 mm
Cutting length, max.: .............................. 375 mm
Cutting speed at rated rpm: .......................15 m/s
Oil tank capacity: .......................................150 ml
Weight with cutter rail and chain: ................5,6 kg
Protection class: ...........................................II /
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 62841.
L sound pressure level ..................... 93,8 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level ........................ 107 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
L sound power level guaranteed ....... 110 dB(A)
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 62841-1
and EN 62841-4-1.
Front Handle under load
Vibration emission value a
K uncertainty = 1.5 m/s
Rear Handle under load
Vibration emission value a
K uncertainty = 1.5 m/s
•
The quoted total vibration value and the quo-
ted noise emission value were measured in
accordance with standardized test procedu-
res and can be used to compare one electric
tool with another.
Anl_GEK_E_2240_SPK7.indb 24 Anl_GEK_E_2240_SPK7.indb 24
= 3.46 m/s
2
h
2
= 5.89 m/s
2
h
2
- 24 -
GB
•
The quoted total vibration value and the quo-
ted noise emission value can also be used to
make an initial assessment of exposure.
Warning:
•
The vibration and noise emission levels
during actual use may vary from the values
quoted, depending on the way in which the
electric tool is used and, in particular, on the
type of workpiece being processed.
•
Try to keep the exposure to vibrations and
noise as low as possible. Exposure to vibra-
tions can be reduced by wearing gloves when
using the tool, for example, and by limiting
the amount of operating time. All stages of
the operating cycle must be considered (for
example, times in which the electric tools are
switched off and times in which the tool is
switched on but operates without load).
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
5. Before starting the equipment
Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
Caution: Do not connect the chainsaw to the po-
wer supply until it has been fully assembled and
the chain tension has been adjusted. Always wear
protective gloves when working on the chainsaw
to protect yourself against injury.
5.1 Assembly of the cutter rail and the saw
chain
•
Carefully unpack all parts and check that they
are complete (Fig. 2-3).
•
Undo the fixing screw of the chain wheel co-
ver (Fig. 4).
13.10.2023 11:48:15 13.10.2023 11:48:15