Publicidad
Idiomas disponibles
Idiomas disponibles
|
ENGLISH
CONNECTIONS
e
Notes on Connection
e
Do not plug the power supply cord into the wall socket, until all the connections are complete.
e
Plug the pins in securely. An incomplete connection will cause noise generation.
e
Connection to the speaker system
OTHER CHANNE
Be
careful
not
to
mistake
the polarity
of the speaker terminals.
SPEAKER SYSTEMS
CAUTION
A or B 4~ 160hm
SPEAKER IMPEDANCE
A + B 8= 1bohm
+
© ©:
© ©
NIPPON COLUMBIA CO., LTD.
For Europe & Multiple Voltage
SPEAKER SYSTEMS
CAUTION
A or B 4 — I6ohm
SPEAKER IMPEDANCE
A + B 8 — I6ohm
mus
||
NORMAL
|
( REMOTO )
ON-OFF
DENON
MODEL NO.
POA-6600
POWER SOURCE
120Y ~ 60e
POWER CONSUMPTION
H
o
WARNING!
RISK OF HAZARDOUS ENERGY!
WAKE PROPER SPEAKER
WARNING : SHOCK HAZARD — DO NOT OPEN.
AVIS ` RISQUE DE CHOC ELECTRIQUE —NE PAS OUVRIR.
A
Fer]
A
e
O
WARNING : TO PREVENT FIRE OR SHOCK HAZARD.
DO NOT EXPOSE
THI
HJ
OSE THIS APPLIANCE TO RAIN OR
105 S004 nos
an
e LINE VOLTAGE (Voltage select
switch) . . . For Multiple voltage
model only.
* The desired voltage may
be
a
set with the VOLTAGE
SE-
LECTOR
KNOB
on the back
panel using a screw driver.
Do not twist the VOLTAGE
SELECTOR
KNOB
with ex-
Line voltage wall outlet
EC
et
Tee
cessive
force.
It
may
be
(Sn
T=
GE
damaged.
|
i
i
If the voltage select switch
I
|
i
I
SRE Stan Iewen
does
not tum
smpothly, see
|
CD player
a qualified serviceman.
|
a
|
=
FH
|
oo
100111
OOOO
LINE VOLTAGE
e
Connection to the speaker system
e
When
connecting the speaker terminals to the speaker systems, make certain to connect the polarities correctly (+to +
and — to —). If the polarities are incorrect when the two are connected, the center area of the sound will be lacking, the
positions of the musical instruments will not be clear, and the stereo directional sensitivity will be impaired.
e
During connection,
be careful that the center wires in the speaker cords do not protrude from the terminals to contact
any other terminal, and that the central wires in the separate speaker cords do not contact each other.
e
Speaker impedance
e
When the A and B terminal sets are to be used separately, the speakers that are to be connected should have a nominal
impedance of 4 to 16 ohm.
e
When the two sets (A + B) are to be used at the same time, use of speakers whose impedance is outside the range from 8
to 16 ohm will result in malfunction. Be careful not to let this happen.
e
Speakers with a lower impedance may cause the protective circuitry to operate.
Models for the U.S. and Canada only. (Case of UL standardized articles)
WARNING!
This amplifier produces a large power output at the speaker termi-
nals, which
means
that a dangerous amount of energy is generated
and that there is the danger of electric shock.
Please perform the
speaker cord connections correctly as follows.
(Making connections that differ from the specified method may give
rise to a shock hazard.)
1) For the speaker connection
cord,
use a cord made with non-
combustible
insulation material with
a VW-1
rating or a cord of
the SPT-1 type or one with higher flexibility.
2) Use a screwdriver to take the screws holding the speaker terminal
SPEAKER
SYSTEM
(A)
SPEAKER
TERMINAL
SPEAKER
~
COVER
cover out.
SYSTEM
(B)
3) Connect the speaker cord specified in 1) to the speaker terminals.
4) Tie the speaker cord, then pass it through the cutout hole in the
speaker terminal cover.
5) Install the speaker terminal cover removed in 2).
Models for destinations other than the U.S. and Canada.
+
e
For regular cords
. Remove
the insulation
Note:
from
the end of each
cord.
. Twist the center wire.
. Turn
the
speaker
ter-
minal
to
loosen
it,
insert
the
center
wire
of the cord, and then
tighten the terminal to
hold the wire in place.
For extra-large cords
1.
Remove
the insulation
from
the
end
of the
cord.
Loosen
and
re-
move
the
end
of the
speaker terminal.
. Insert the center
wire,
and bend back the wire.
. Insert
the cord
in the
terminal,
and turn the
terminal to the right to
tighten it.
The
knob
on this speaker
terminal
can
be
removed
from
the
Amplifier.
Be
careful
not
to
lose these
knobs, or mix up the left
and
right sides
or polari-
ties. Follow the indication
provided on the back panel
for proper handling.
Publicidad
