Publicidad
Idiomas disponibles
Idiomas disponibles
TO CLEANBATTERY AND TERMINALS
Corrosionanddirt onthe batteryandtermi-
nalscan causethe batteryto "leak"power.
1, Removeterminalguard,
2. DisconnectBLACK battery cable first
then RED battery cable and remove
batteryfrom tractor°
3, Rinsethebattery withplainwateranddr,/.
4, Cleanterminalsandbatterycable ends
with wire brushuntilbright.
5, Coatterminalswithgreaseor petroleum
jelly.
6, Reinstall battery (See "REPLACING
BATTERY"in the SERVICEAND AD-
JUSTMENTSsectionofthis manual),
TRANSAXLE
MAINTENANCE
The transmission
fan and cooling fins should
be kept clean to assure proper cooling_ Do
not attempt to clean fan or transmission
while
engine
is running or while the transmission
is hot. To prevent possible damage
to seals,
do not use high pressure
water or steam to
clean transaxle.
• Inspect cooling
fan to be sure fan blades
are intact and clean,
,
inspect cooling fins for dirt, grass clippings
and other materials_ To prevent damage to
seals, do not use compressed
air or high
pressure
sprayer
to clean cooling fins.
TRANSAXLE
PUMP FLUID
The transaxle
was sealed at the factory and
fluid maintenance
is not required
for the life
of the transaxle.
Should the transaxle
ever
leak or require servicing,
contact your near-
est Sears or other qualified
service
center.
V-BELTS
Check V-belts for deterioration
and wear after
100 hours of operation
and replace if neces-
saryo The belts are not adjustable°
Replace
belts if they begin to slip from wear.
ENGINE
LUBRICATION
Only use high quality detergent
oil rated with
API service classification
SG-SL.
Select the
oi!'s SAE viscosity
grade according
to your
expected
operating
temperature.
SAE VISCOSITY
GRADES
o2 4o
_
_0
_i_
...... _MP
ERAt_RE'
RAN'{_'E"A"NTiC [PATF-D B EFOR E NEXT OIL CHA NGE
NOTE: Although
multi-viscosity
oils (5W30,
10W30 etc,) improve starting in cold weather,
they will result in increased
oil consumption
when used above 32°E
Check your engine
oil level more frequently
to avoid possible
engine damage
from running
low on oil,
Change the oil after every 50 hours of opera-
tion or at least once a year if the tractor
is
not used for 50 hours in one year.
Checkthe
crankcase
oil level before starting
the engine
and after each eight (8) hours
of operation,
Tighten
oil fitl cap!dipstick
securely
each time you check the oil level.
TO CHANGE ENGINE OIL
Determine temperature
range expected
before oil change. All oil must meet API
service classification SG-SL.
• Be sure tractor is on level surface.
• Oil will drain more freely when warm.
• Catch oil in a suitable container.
1, Remove oil fill cap/dipstick, Be careful
not to allow dirt to enter the engine when
changing oil.
2_ Remove yellow cap from end of drain
valve and install the drain tube onto the
fitting,
3. Unlock drain valve by pushing inward
slightly and turning counterclockwise.
Closed
and
Locked
Yellow
Oil Drain Valve
Drain
Tube
4.
To open, pull out on the drain valve.
5.
After oil has drained completely, close and
lock the drain valve by pushing
inward
and turning
clockwise
until the pin is in
the locked position
as shown.
6o Remove
the drain tube and replace
the
cap onto the end of the drain valve,
7.
Refill engine with oitthrough
oilfill dipstick
tube.
Pour slowly.
Do not overfill.
For
approximate
capacity
see "PRODUCT
SPECIFICATlONS"sectionofthis
manuat°
8.
Use gauge
on oil fill cap/dipstick
for
checking
level.
Insert dipstick
into the
tube and rest the oil fill cap on the tube.
Do not thread the cap onto the tube when
taking
reading.
Keep oil at "FULL_ line
on dipstick.
Tighten
cap onto the tube
securely
when finished.
23
Publicidad
