Descargar Imprimir esta página

Jata JVTE4233 Instrucciones De Uso página 13

Ventilador de techo blanco
Ocultar thumbs Ver también para JVTE4233:

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 1
• Subsequently, insert the motor mount anchor (5) into the upper motor mount (7) unscrewing the screws a
little and secure it by inserting the pin with the retaining clip and tightening the screws. (Fig 8)
• Place the engine trim (6).
• Insert the upper pin of the motor support anchor (5), keeping the connection cables apart, and raise the
plunger to the end. Next, tighten the screw to leave it well fixed. (Fig 9)
• Unscrew the side screws of the roof trim (4). (Fig 10)
• Make the holes in the ceiling, taking into account the previous indications about the types of surfaces, and
anchor the ceiling support frame (2).
• Make sure that the electrical current is disconnected.
• Place the semi-assembled fan by inserting the piston of the motor support anchor (5) into the ceiling support
frame (2) matching the groove of the piston with a small notch in the support frame. (Fig 11)
• Place the Receiver (3) on the ceiling support frame (2). Note that the wires from the receiver must be on the
side of the receiver where the power strip is located. (Fig 12)
• Then, make the connections according to the following diagram. (Fig 13)
• Once connected, place the roof trim making it coincide with the holes of the support frame (2) by turning
and insert the screws.
• Once located on the ceiling, place the ceiling lamp (10) making it rotate on the LED support (8). You can now
connect the electrical current. (Fig 14)
• The balancing kit (12) should only be used if there is considerable wobble in the fan after fully assembled:
- Turn on the fan and select maximum power, look at the blade that oscillates the most.
- Turn off the fan and wait for it to come to a complete standstill. Place the balance clip in the middle of
the blade on the blade that wobbles the most. Turn on the fan and see if the oscillation has increased or
decreased.
- Repeat this process on all the blades, observing which one achieves less oscillation.
- Once the blade is selected, it will be tested by placing the balance clip a little closer to the tip or then a
little closer to the anchor, observing where the oscillation is less in movement.
- Remove the clip where the oscillation is less and place a balance weight sticking it in the middle area at
the top of the blade.
- If the problem continues, you can repeat the operation again with more balance weights.
INSTRUCTIONS OF USE
• To link the fan with the remote control, press the on/off button (a) on the remote control for 5 seconds until
you hear a sound, thus completing the link successfully.
• Remote control (13) (Fig 15):
- On / off light button (a).
- Speed control (1-2-3-4-5-6) (b).
- On button /off fan button (c).
- Timer (1H-2H-4H-8H) (d).
- Light intensity button (e).
- Reverse function (f).
• Switch on the fan by pushing the button (c), to turn it off press it again.
• Press the speed control (b) to choose the desired speed from 1 to 6.
• To switch on the light, push the lighting button (a):
- 1 pulsation: Cold light.
- 2 pulsations: Intermediate light.
- 3 pulsations: Warm light.
• To program it, press the timer (d) and select the desired time (1-2-4-8 hours)
• Winter mode (f) changes the direction of rotation of the blades, always try to do it when the motor is stopped.
To return to the initial direction of rotation, press it again. This option is perfect for lowering the heat in the
room and thus having a cozier thermal sensation in winter and greater energy efficiency. (Fig 16)
13

Publicidad

loading