Publicidad
Idiomas disponibles
Idiomas disponibles
5.
The contained lithium-ion batteries are subject to the
Dangerous Goods Legislation requirements.
For commercial transports e.g. by third parties or forwarding
agents, special requirement on packaging and labeling must be
observed.
For preparation of the item being shipped, consulting an expert
for hazardous material is required. Please also observe possible
more detailed national regulations.
Do not use the machine near high-voltage electrical power
6.
transmission lines. Doing so may result in a malfunction or
breakdown of the machine or battery.
7.
Store the product in a safe place out of the reach of children.
8.
Never service damaged battery packs. Service of battery
packs should only be performed by the manufacturer or autho-
rized service providers.
SAVE THESE INSTRUCTIONS.
CAUTION: Only use genuine Makita batteries. Use of
non-genuine Makita batteries, or batteries that have been altered,
may result in the battery bursting causing fires, personal injury and
damage. It will also void the Makita warranty for the Makita tool and
charger.
Tips for maintaining maximum battery life
1.
Never recharge a fully charged battery. Overcharging short-
ens the battery service life.
2.
Charge the battery with ambient temperature at 10 °C - 40 °C
(50 °F - 104 °F). Let a hot battery cool down before charging
it.
Charge the battery if you do not use it for a long period
3.
(more than six months).
Names of parts
► Fig.2
1.
Robotic Mower
2.
"STOP" button
3.
Display cover
4.
Rear wheel
5.
LED
6.
Charging socket
7.
Control panel
8.
Top cover
9.
Chassis
10. Slider shaft
11. Rubber retainer
12. Front wheel
13. Power switch
14. Grip
15. USB cap
(Do not open. This is for maintenance servicing.)
16. Blade cover
17. Blade base
18. Mower blade
19. Skid plate
20. Charging station
21. Station base
22. Charging terminal
23. Terminal cover
24. Station housing
25. Station indicator
26. Wire cover
27. Boundary wire
28. Guide wire
29. Wire
30. Peg
31. Connector
32. Coupler
33. AC adapter
(The plug shape will differ from region to region.)
34. Cabtire cable
35. Screw peg
(For fixing the charging station)
36. Hex wrench 6
Noise
The typical A-weighted noise level determined according to
EN50636-2-107:
Sound pressure level (L
Sound power level (L
WA
Uncertainty (K) : 3.1 dB (A)
The noise level under working may exceed 80 dB (A).
NOTE: The declared noise emission value(s) are measured by the
standard test method, and may be used for mutual comparison
between machines.
NOTE: The declared noise emission value(s) may also be used in a
preliminary assessment of exposure.
WARNING: The noise actually emitted in use of the machine
may differ from the declared value(s) depending on the usage
of the machine, and especially the type of material to be
processed.
WARNING: Be sure to take safety measures to protect work-
ers based on estimates of exposure under the actual condi-
tions of use (consider the entire operating cycle including the
time the machine is switched off and the idling time in addition
to the operating time).
Declarations of Conformity
For European countries only
The Declarations of conformity are included in Annex A to this instruc-
tion manual.
Introduction of separately sold items
CAUTION: These accessories or attachments are recom-
mended for use with your Makita products specified in this
manual. The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory or attach-
ment for its stated purpose.
For details of separately sold items, refer to the catalog or contact the
dealer or our sales office.
•
Blade set
—
Set of mower blades and fixing screws
•
Wire
•
Wire repair kit
—
Set of wire, couplers, and pegs
•
Peg
•
Coupler
NOTE: Some separately sold items in the list may be supplied
with the machine as standard accessories at the time of purchase.
Standard accessories may differ depending on the country of
purchase.
16
ENGLISH
) : 70 dB(A) or less
pA
) : 59 dB (A)
Publicidad
