JOCCA 1618 Manual De Instrucciones página 13

24-E
-To be cautious with any risk that sprayed material can cause and
consult indications on a containers or information provided by sup-
plier about material for spraying, including requirements for personal
protection using equipment.
-Do not spray any material if you do not know its risk.
INSTRUCTIONS FOR USE
Assembling of a device:
-It is quite easy to assemble a gun – take a paint support and fit it
into the lateral of a unit body, see picture 1.
-Then take one edge of a flexible tube and fit it into a unit body and
another edge – into a spraying gun, see picture 2.
-Finally take a carrying tape for hanging and fix it on a motor base as
it is shown on the picture 3.
Preparation of a zone for painting:
-Before start painting, ensure that an area you want to paint is clean
and dust free.
-It is also recommended to use masking tape to cover areas you do
not want to paint.
Preparation of paint and liquids to spray:
-This device can spray different types of paint and different liquids
like varnishes, disinfectants, waxes, pesticides etc.
-Paint should be diluted and free of paint particles or grains. Grains
of paint or particles can block a nozzle, thus it is not recommended to
use grain painting.
-To start spraying it is necessary to measure viscosity – to mix paint
or liquid you want to use and to fill a viscometer with it, see picture
4.
-To see if liquid or paint is diluted well and its viscosity is correct, a
viscometer should empty in less than 30 seconds.
-If a viscometer empties in more than 30 seconds, you have to dilu-
te liquid or paint before using it – maximum viscosity for this device is
30 seconds. Never use liquid or paint that exceeds 30 seconds of
dripping time. If dripping time is less than 15 seconds, paint is too
liquid to apply and it will flow down the walls, try to thicken paint.
-To dilute liquid or paint, pay attention if this paint has water base, it
will be diluted with water then. For other types of liquids you can use
diluent or alcohol. To be sure about proper way of diluting liquids for
spraying you must consult a manufacture of paint, varnish etc.
Follow the next guide table:
Liquid or paint type
Varnishes
Clear varnish/aluminium paint
Acrylic paint
Wood coating/pesticides
-Once you achieve correct viscosity, mix well liquid for sparring and
fill a tank of a device with it. To separate a tank trigger, turn clockwi-
se and open a tank, then pour liquid inside and put back a trigger on
a tank and screw counter clockwise on it.
-Plug in a device ensure that a switch On/Off is in position 0 (swit-
ched Off).
-For better operating, you can place a hanging tape of a shoulder
having both hands free to work. It is recommended to take out a sup-
port of a gun during its using for better operating of a device.
-Before start spraying, try a gun on some surface and adjust spra-
ying amplitude with help of an adjusting screw, see picture 5.
-If you want to reduce spraying flow, turn a screw clockwise.
-If you want to increase spraying flow, turn a screw counter clockwi-
se.
-This device can spray in 3 positions: vertical, horizontal and circle,
depending of nozzle position, see picture 6.
-Having flow and jet position adjusted, take a device by its handle
and direct a nozzle towards you want to spray liquid, press a gun trig-
ger, a device will start spraying liquid then.
-It is recommended keep a nozzle in 25-30 cm from a surface to be
painted and paint in straight and parallel to avoid spills, see picture
7.
-Once you have painted or sprayed the entire necessary surface, put
a switch in position 0 (switch Off) and unplug a device.
-If you want to spray over the second layer, consult a manufacture
E-25
Dripping time in seconds
Not diluted
15-30 seg
20-30 seg
Not diluted (max. 30 seg)