EINHELL GC-CT 18/24 Li P Manual De Instrucciones Original página 18

tor housing in the direction of the arrow as shown
in Fig. 6. Make sure it clicks into place (Fig. 7).
5.4 Fitting the blade plate (Figs. 8-9)
Fit the blade plate (Item 4) onto the mounting
shaft and fasten it with the screw (Item 7).
5.5 Inserting the blade (Fig. 10)
Place the larger opening of the blade (Item 3) in
the blade mount (D) on the blade plate (Item 4)
and pull it outwards in the direction of the arrow
until the blade clicks into place as shown in Fig.
11.
5.6 Installing the battery (Fig. 12/13)
Press the side pushlock (E) buttons of the battery
pack as shown in Fig. 12 and push the battery
pack into the mount provided. When the battery
pack is positioned as in Fig. 13, make sure that
the pushlock buttons latch in place! To remove the
battery pack, proceed in reverse order.
5.7 Charging the battery (Fig. 14)
1. Take the battery pack out of the equipment.
Do this by pressing the side pushlock buttons.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(J) into the mains socket outlet. The green
LED will then begin to fl ash.
3. Insert the battery pack (K) into the battery
charger (J).
4. In section „Charger indicator" you will fi nd a
table with an explanation of the LED indicator
on the charger.
The battery pack can become a little warm during
the charging. This is normal. If the battery pack
fails to charge, check:
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts
If the battery pack still fails to charge, send
•
the charging unit
•
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
Anl_GC_CT_18_24_Li_P_Solo_SPK13_3411103.indb 18 Anl_GC_CT_18_24_Li_P_Solo_SPK13_3411103.indb 18
GB
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
5.8 Battery capacity indicator (Fig. 15)
Press the button for the battery capacity indicator
(Item F). The battery capacity indicator (Item H)
shows the charge status of the battery using 3
LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED fl ashes:
The battery is empty, recharge the battery.
All LEDs blink:
The battery temperature is too low. Remove the
battery from the equipment, keep it at room tem-
perature for one day. If the fault reoccurs, this me-
ans that the rechargeable battery has undergone
exhaustive discharge and is defective. Remove
the battery from the equipment. Never use or
charge a defective battery.
6. Operation
To obtain maximum performance from your grass
trimmer, please follow these instructions:
•
Never use the grass trimmer without the
guard.
•
Do not mow grass when it is wet. The best
results are achieved with dry grass.
•
To switch on your grass trimmer, press the
ON/OFF switch (Fig. 13/Item 1).
•
To switch off your grass trimmer, let go of the
On/Off switch again (Fig. 13/Item 1).
•
Do not allow the grass trimmer near the grass
until the switch is pressed, i.e. the grass trim-
mer is in operation.
•
To cut properly, swing the machine sideways
while moving forwards. Keep the grass trim-
- 18 -
08.08.2023 15:56:02 08.08.2023 15:56:02