Ryobi RYi2300BT Manual Del Operador página 18

Generador inversor digital con bluetooth
Ocultar thumbs Ver también para RYi2300BT:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

 Remove the fuel cap slowly.
 Fill the fuel tank to 1 in. below the top of the fuel neck.
 Replace and secure the fuel cap.
WARNING:
Always shut off engine before fueling. Never remove
fuel cap or add fuel to a machine with a running or hot
engine. Make sure the unit is sitting on a flat, level sur-
face and only add fuel outdoors. If the engine is hot, let
the unit cool for at least five minutes before adding fuel.
After fueling, immediately replace fuel cap and tighten
securely. Move at least 30 ft. from refueling site before
starting engine. Do not smoke and stay away from open
flames and sparks! Failure to follow these instructions
could result in a fire and cause serious personal injury.
NOTE: Always use unleaded gasoline with a pump octane
rating of 86 or higher. Never use old, stale, or contaminated
gasoline, and do not use an oil/gas mixture. Do not allow dirt
or water into the fuel tank. Do not use E85 fuel.
STARTING THE ENGINE
See Figures 5 - 7.
NOTICE:
On a level surface with the engine off, check the lubricant
level before each use of the generator.
NOTE: If location of generator is not level, the unit may not
start or may shut down during operation.
To start generator the first time:
 Add engine lubricant per the Operator's Manual
instructions.
 Place the Easy Start dial to the COLD START (CHOKE)
position.
 Fill the fuel tank per the Operator's Manual instructions.
 Pull the recoil starter until the engine starts.
 Allow the engine to run for 15-30 seconds, then move
the Easy Start dial to the RUN/RE-START position.
To start subsequent times:
 Unplug all loads from the generator.
 Turn the Easy Start dial to the COLD START position.
NOTE: When the Easy Start dial is in the COLD START
(top) position, the fuel will flow from the fuel tank to the
engine. If engine is warm, turn the Easy Start dial to the
RUN/RE-START (middle) position.
 Pull the recoil starter until the engine runs.
NOTE: Do not allow the grip to snap back after starting;
return it gently to its original place. Initial starting of the
unit may require additional pulls to prime the fuel pump.
 Allow the engine to run for 15-30 seconds, then move
the Easy Start dial to the RUN/RE-START position.
OPERATION
STOPPING THE ENGINE
See Figures 5 - 6.
 Remove any load from the generator.
 Place the Easy Start dial in the OFF/STORAGE position.
To stop the engine in an emergency situation:
 Place the Easy Start dial in the OFF/STORAGE position.
WARNING:
While operating and storing, keep at least 3 feet of clear-
ance on all sides of this product, including overhead.
Allow a minimum of 30 minutes of "cool down" time
before storage. Heat created by muffler and exhaust
gases could be hot enough to cause serious burns and/
or ignite combustible objects.
PAIRING THE BLUETOOTH
See Figure 8.
Installing the RYOBI GENCONTROL app on your Bluetooth
enabled iOS or Android device allows you to view and control
many of the generator's functions from your device.
 From the app store on your iOS or Android Bluetooth
enabled device, locate and install the RYOBI
GENCONTROL™ app.
 Open the app and follow the directions as shown in the
GENControl app.
NOTE: Make sure Bluetooth
 Start the generator. Push and hold the "Push and Hold to
Pair" button below the LCD panel on the generator until
the LCD panel displays "Paring Mode."
 The LCD screen on the generator and the app on your
device will indicate a successful pairing.
NOTE: If the generator and app do not pair, make sure
that "Pairing Mode" is displayed during the pairing process
and that Bluetooth
 Press the menu icon in the top left corner of the screen.
This will show you the available features that can be
controlled through the app.
MOVING THE GENERATOR
See Figure 9.
 Place the Easy Start dial in the OFF/STORAGE position. In
the OFF/STORAGE position, the fuel valve will be closed
and prevent any gas flow.
 Allow 30 minutes of "cool down" time before storing the
machine.
 Pull the retractable handle out or carry by the carry handles.
 Facing the front of the generator, grasp the folding handle
firmly with one hand.
14 — English
GENERATOR
®
is enabled on your device.
®
is enabled on your device.
®
®
®

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Ryi2300bta

Tabla de contenido