Bosch CG270 Instrucciones De Montaje página 6

B) Flush installation (fig. 3b)
Complete a normal installation of the appliance making sure
1.
that it is surrounded by a uniform slot. The hob surface should
be slightly below the work surface.
For tile worktops, if necessary, raise the bearing surfaces with
strips resistant to water and temperatures.
Check the operation and position of appliance.
2.
Fill the gap between the worktop and hob with suitable
3.
conventional silicone adhesive in any colour you wish.
Note: If unsuitable silicone adhesive is used on natural stone
surfaces this can produce permanent colouring. Our Technical
Assistance Service can provide you with the most suitable
adhesive (code 310818, stainless steel colour C197). Please
note the manufacturer's instructions for use.
Smooth the silicone adhesive with a scraper or wet finger
4.
moistened with soap and water before it forms a layer.
Allow the silicone adhesive to dry before using the appliance.
5.
Removal of hob
Turn off the appliance's electricity and gas supply.
Unscrew the clips and proceed in the reverse order to
installation.
Gas connection (fig. 4)
The end of the inlet connection point of the gas hob has a 1/2"
thread (20.955 mm) that allows for:
A fixed connection.
■
Connection using a flexible pipe (L min. 1 m - max. 3 m).
■
The watertight seal (034308) supplied must be inserted
between the manifold outlet and the gas supply.
You must prevent the pipe from coming into contact with
moving parts of the kitchen unit (for example, a drawer) and
prevent access to any spaces which might become obstructed.
Do not move the L-tube from the factory-fitted position,
regardless of the connection type.
If you need to make a cylindrical connection, replace the factory-
fitted L-tube with the one in the accessory bag. Fig. 4a.
Please remember to insert the seal.
: Danger of leaks!
If any connection is handled, check the seal.
The manufacturer is not liable for any connection leaking, after
being handled.
Electric connection (fig. 5)
This appliance is type "Y": the supply cable can only be
changed by the Technical Assistance Service and not the user.
The cable type and minimum cross-section must be respected.
The hobs are supplied with a power cable with or without a wall
socket plug.
Appliances with plugs must only be connected to sockets that
have earth wires correctly installed.
Provide an omnipolar cut-off switch with a minimum contact
opening of 3 mm (except for plug connections, if the user has
access to it).
Changing the gas type
If the country's regulations allow, this appliance can be adapted
to other types of gas (see specifications plate). The components
required for this are in the transformation kit supplied
(depending on the model) or are available from our Technical
Assistance Service.
Important: After finishing, stick the sticker, indicating the new
gas type, close to the specifications plate.
The following steps should be taken:
A) Changing the nozzles (fig. 6):
Remove the pan supports, burner caps and diffusers.
1.
Change the nozzles using the spanner code 340847 (code
2.
340808 for double-flame burners or triple-flame burners)
provided by our Technical Assistance Service, see table II,
taking special care to ensure that the nozzle does not fall
when it is removed from or fitted to the burner.
Ensure that it is completely tightened in order to guarantee the
seal.
Primary air adjustment is not necessary with these burners.
Position the diffusers and burner caps on the corresponding
3.
rings and the pan supports on their fasteners.
B) Adjusting the taps (Fig. 7):
Set the control knobs to minimum.
1.
Remove the control knobs from the taps. It has a flexible
2.
rubber valve reinforcing ring. Press with the tip of the
screwdriver to access the tap's adjusting screw.
Never remove the valve reinforcing ring. The valve reinforcing
rings guarantee the watertightness of the appliance's interior
from liquids and dirt, which might otherwise prevent its correct
operation.
Adjust the minimum ring setting by turning the by-pass screw
3.
using a flat head screwdriver.
Depending on the gas to which your appliance is going to be
adapted, see table III, carry out the corresponding action:
A: firmly tighten the by-pass screws.
B: loosen the by-pass screws until the gas flow from the
burners is correct.
C: the by-pass screws need to be changed by an authorised
engineer.
D: do not touch the by-pass screws.
When adjusting the control knob between maximum and
minimum, the burner does not go out, nor is there a flame
backdraught created.
If the by-pass screw cannot be accessed, disassemble the
grease drip tray, which is fitted to the hob with a series of
screws. The following steps must be taken to remove it:
Remove all pan supports, burner caps, diffusers and control
1.
knobs.
Remove the screws from the burners.
2.
To reinstall the appliance, proceed in the reverse order to
3.
disassembly.
Never remove the tap spindle (Fig. 8). In the event of a
malfunction, change the whole tap.
es
Û
In stru c ci one s de m on taj e
Indicaciones de seguridad
Lea las instrucciones del aparato antes de proceder a su
instalación y uso.
Las imágenes representadas en estas instrucciones tienen
carácter orientativo.
El fabricante queda exento de toda responsabilidad si no se
cumplen las disposiciones de este manual.
Este aparato se debe utilizar únicamente en lugares
suficientemente ventilados. No se debe conectar a un
dispositivo de evacuación de los productos de combustión.
Todos los trabajos de instalación, conexión, regulación y
adaptación a otros tipos de gas deben ser efectuados por un
técnico de instalación autorizado, respetando toda la
normativa y legislación aplicables y las prescripciones de las
compañías locales proveedoras de gas y electricidad. Se
pondrá especial atención a las disposiciones aplicables en
cuanto a la ventilación.
Se recomienda llamar a nuestro Servicio Técnico para la
adaptación a otros tipos de gas.
Este aparato ha sido diseñado solo para uso doméstico, no
estando permitido su uso comercial o profesional. Este aparato
no puede ser instalado en yates o caravanas. La garantía
únicamente tendrá validez en caso de que se respete el uso
para el que fue diseñado.
Antes de la instalación, compruebe que las condiciones de
distribución local son compatibles con el reglaje del aparato
que figura en la placa de características (naturaleza y presión
del gas, potencia, voltaje). Ver tabla I.
Antes de cualquier actuación corte la alimentación eléctrica y
de gas del aparato.
El cable de alimentación debe fijarse al mueble para evitar que
toque partes calientes del horno o placa de cocción.
Los aparatos con alimentación eléctrica deben conectarse a
tierra obligatoriamente.
No manipule el interior del aparato. Si es preciso, llame a
nuestro Servicio Técnico.
Antes de la instalación
Este aparato corresponde a la clase 3, según la norma EN 30-
1-1 para aparatos a gas: aparato encastrado en un mueble.
El mueble en el que se instale el aparato debe estar
convenientemente fijado y ser estable.
Los muebles próximos al aparato, los revestimientos
estratificados y la cola que los fija deben ser de materiales no
inflamables y resistentes al calor.
Este aparato no se puede instalar sobre neveras, lavadoras,
lavavajillas o similares.