Craftsman 139.53990DS Manual Del Propietário página 17

iNSTALLATiON STEP 6
Irestall the Door Control
Locate door control within sight of door, at a
minimum height of 5 feet (1.5 m) where small
children cannot reach, away from moving parts of
door and door hardware. If installing into drywall, drill
5/32" holes and use the anchors provided. For
pre-wired installations (as in new home construction),
it may be mounted to a single gang box (Figure 1).
1. Strip 7/16" (11 mm) of insulation from one end of
bell wire and connect to the two screw terminals
on back of door control by color: white wire to
2 and white/red wire to the 1 (Figure 2).
2. Remove cover by gently prying at slot in top of the
cover with a small flat head screwdriver (Figure 3).
Fasten with 6ABxl" self-tapping screws (drywall
installation) or 6-32x1" machine screws (into gang
box) as follows:
• Install bottom screw, allowing 1/8" (3 mm) to
protrude above wall surface.
• Position bottom of door control on screw head
and slide down to secure. Adjust screw for
snug fit.
• Drill and install top screw with care to avoid
cracking plastic housing. Do not overtighten.
• Insert top tabs and snap on cover.
3. (For standard installation only) Run bell wire up
wall and across ceiling to motor unit. Use insulated
staples to secure wire in several places. Do not
pierce wire with a staple, creating a short or open
circuit.
4. Strip 7/16" (11 mm) of insulation from end of bell
wire. Connect bell wire to the quick-connect
terminals as follows: white to white and white/red
to red (Figure 4).
NOTE: When connecting multiple door controls to
the opener, twist same color wires together. Insert
wires into quick-connect holes: white to white and
red/white to red.
5. Position the antenna wire as shown.
6. Use tacks or staples to permanently attach
entrapment warning label to wall near door control,
and manual release/safety reverse test label in a
prominent location on inside of garage door.
NOTE: DO NOT connect power and operate opener
at this time. The trolley will travel to the full open
position but will not return to the close position until
the sensor beam is connected and properly aligned.
To Replace,
Insert Top
Tabs First
To prevent possible SERIOUSINJURYor DEATHfrom
electrocution:
• Be sure power is NOT connected BEFORE installing
door control.
• Connect ONLYto 24 VOLT low voltage wires.
To prevent possible SERIOUSINJURYor DEATHfrom a
closing garage door:
• Install door control within sight of garage door, out of
reach of children at a minimum height of 5 feet
(1.5 m), and away from ALL moving parts of door.
• NEVERpermit children to operate or play with door
control push buttons or remote control transmitters.
• Activate door ONLYwhen it can be seen clearly, is
properly adjusted, and there are no obstructions to door
travel.
• ALWAYSkeep garage door in sight until completely
closed. NEVERpermit anyone to cross path of closing
garage door.
HARDWARE SHOWN ACTUAL SIZE
1_ Insulated Staples
(Not shown)
(std installation)
(Gang box installation) Drywall Anchors
Figure 1
PRE-WIRED II __1
INSTALLATION _
24 Volt
I._£ _-'1fl I
2-Conductor
_'q-LtlJ
Bell Wire in
Gang Box
Figure 2
B_TOp
Mounting
Hole
Terminal
Screws
Bottom
Mounting
Wire Hole
(BACK VIEW)
Figure 3
17
Figure 4
2-Conductor
Push Bar Bell Wire
Lock
Light
) C
@ @
Quick-Connect
Terminals
To release or insert wire,
push in tab with
screwdriver tip
Strip wire 7/16" (11 ram)
Door Control
Connections
Red White Grey
Antenna