Publicidad
Idiomas disponibles
Idiomas disponibles
12 | English
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Do not touch any application tools or adjacent housing
u
components shortly after operation. These can become
very hot during operation and cause burns.
The application tool may jam during drilling. Make
u
sure you have a stable footing and hold the power tool
firmly with both hands. Otherwise you could lose con-
trol of the power tool.
Take care when carrying out demolition work using
u
the chisel. Falling fragments of the demolition material
could injure you or any bystanders.
Hold the power tool firmly with both hands and make
u
sure you have a stable footing. The power tool can be
more securely guided with both hands.
Symbols
The following symbols may be important for the operation of
your power tool. Please take note of these symbols and their
meaning. Correctly interpreting the symbols will help you to
operate the power tool more effectively and safely.
Symbols and their meaning
To change the application tool, pull back
the locking sleeve.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended Use
The power tool is intended for hammer drilling in concrete,
masonry and stone, as well as for chiselling work.
Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1)
Dust protection cap
(2)
Locking sleeve
(3)
Mode selector switch
1 609 92A 743 | (18.05.2022)
(4)
On/off switch
(5)
Handle (insulated gripping surface)
(6)
Speed/impact rate preselection thumbwheel
(7)
Auxiliary handle (insulated gripping surface)
Technical Data
Rotary hammer
Article number
Rated power input
Rated speed
Impact rate
Impact energy per stroke ac-
cording to EPTA-Proced-
ure 05:2016
Chisel positions
Tool holder
Lubrication
Max. drilling diameter
– Concrete (with hammer
drill bit)
– Concrete (with break-
through drill bit)
– Concrete (with hollow
core bit)
Weight according to EPTA-
Procedure 01:2014
Protection class
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.
Noise/Vibration Information
Noise emission values determined according
to EN IEC 62841-2-6.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 94 dB(A); sound power
level 105 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
Vibration total values a
(triax vector sum) and uncertainty K
h
determined according to EN IEC 62841-2-6:
Hammer drilling into concrete: a
h
2
Chiselling: a
=9.0 m/s
, K=1.5 m/s
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
GBH 5-40 D
3 611 B69 0..
W
1100
-1
min
170–340
-1
min
1500–2900
J
8.5
12
SDS max
Central permanent
lubrication
mm
40
mm
55
mm
90
kg
6.8
/ II
2
2
=16.5 m/s
, K=2.3 m/s
,
2
,
Bosch Power Tools
Publicidad
