Assembly Instructions Prior To Start-Up; Start-Up And Operation; Cleaning And Disinfection - Riester ri-magic LED Instrucciones Para El Uso

4. Assembly instructions prior to start-up

a) ri-magic ® LED desk model
Attach universal clamp (1) and screw set (2) to a desk or wall rail.
Insert universal light (4) from top into the bore of the screw clamp and fix
with the knurled bolt (5). Connect cable plug (6) of the power pack (7) to
the socket (8) from below until engaging with a click. Connect a transformer
(7) to the socket. The light is now ready for operation.
b) ri-magic ® LED wall model
Hold wall bracket (1a) to the desired point on the wall and mark 4 holes for
dowels. Remove wall bracket and drill the 4 marked holes. Insert dowels
into the wall. Apply wall bracket and fix with screws. Insert light (4) into
bracket from above and fix by the locking screw (3a) on the side. Connect
cable plug (6a) of power pack (7a) to socket (8a) from below until it enga-
ges with a click. Connect transformer (7a) to the socket. The light is now
ready for operation.
Caution:
The wall must absolutely be solid enough for a good and guaranteed fixati-
on of the diagnostic lamp.
Please only use the included screws and anchors.
Possibility of alternative use of 6 mm anchors with lens head screw DIN 95
3 x 40 mm.
c) ri-magic ® LED stand model
Push bracket (17) into the tripod tube (11) and insert tripod tube (11) and
bracket (17) into the mobile bottom section (12) by fixing with the knurled
bolt (18) on the side and fix with the enclosed bolt (13) and locking ring
(14). The tripod (base) is provided with 5 castors, two of which may be
locked (15). Tilt lever (16) down for locking. Put universal lamp from the top
in the adaptor and fix it with a hexagon bolt (key encl.). Connect cable plug
(6b) of power pack (7b) to the socket (8b) on the side until an audible click
is heard. The light is now ready for operation.

5. Start-up and operation

Initially connect the cable plug (6,a,b) to the socket (8,a,b). Connect power
pack (7,a,b) to the mains socket. Voltages on the rating plate of the mains
adapter must be noted at all times. There are two optional voltages: 230 V
and 120 V.
On-Off
Turn the rheostat (9) in clockwise direction. When a click is heard, the light
is switched on.
Turn the rheostat (9) in counter-clockwise direction until a click is heard.
The light is now switched off.
The Diagnostic lamp can also be interrupted from the main power supply
by removing the plug connector out of the socket.
Rheostat
The desired light intensity may be set by turning the rheostat (9). Increase
light intensity by turning in clockwise direction and decrease by turning in
counter-clockwise direction.
Focusing
A focusing ring (10) is provided at the front of the light head for controlling
the light cone of the light.
Note:
• The flexible arm of the light should not be bent in a too small radius in
order to prevent premature material fatigue.
• For normal operation of the light, the bracket (4) and the universal clamp
(1) and/or the tripod bracket (17) will heat up around the socket (8,a,b).

6. Cleaning and disinfection

Prior to cleaning or disinfection of the light, disconnect plug
from mains socket
Cleaning and/or disinfection
The ri-magic ® LED examination light may be if necessary externally clea-
ned with a damp cloth. In addition, the following disinfectants may be used
for disinfection:
Aldehyde (formaldehyde, glutaraldeyhde, aldehyde derivatives), surfactants
or alcohols. Means for cleaning or disinfection may be a soft, possibly
lint-free cloth or Q-tips.
Sterilisation
Please do not sterilize the ri-magic
8
LED.
®